diff options
Diffstat (limited to 'drivers/mtd/nand/nand_base.c')
| -rw-r--r-- | drivers/mtd/nand/nand_base.c | 317 |
1 files changed, 224 insertions, 93 deletions
diff --git a/drivers/mtd/nand/nand_base.c b/drivers/mtd/nand/nand_base.c index 44d5b12..eee5115 100644 --- a/drivers/mtd/nand/nand_base.c +++ b/drivers/mtd/nand/nand_base.c @@ -28,6 +28,24 @@ * among multiple independend devices. Suggestions and initial patch * from Ben Dooks <ben-mtd@fluff.org> * + * 12-05-2004 dmarlin: add workaround for Renesas AG-AND chips "disturb" issue. + * Basically, any block not rewritten may lose data when surrounding blocks + * are rewritten many times. JFFS2 ensures this doesn't happen for blocks + * it uses, but the Bad Block Table(s) may not be rewritten. To ensure they + * do not lose data, force them to be rewritten when some of the surrounding + * blocks are erased. Rather than tracking a specific nearby block (which + * could itself go bad), use a page address 'mask' to select several blocks + * in the same area, and rewrite the BBT when any of them are erased. + * + * 01-03-2005 dmarlin: added support for the device recovery command sequence for Renesas + * AG-AND chips. If there was a sudden loss of power during an erase operation, + * a "device recovery" operation must be performed when power is restored + * to ensure correct operation. + * + * 01-20-2005 dmarlin: added support for optional hardware specific callback routine to + * perform extra error status checks on erase and write failures. This required + * adding a wrapper function for nand_read_ecc. + * * Credits: * David Woodhouse for adding multichip support * @@ -41,7 +59,7 @@ * The AG-AND chips have nice features for speed improvement, * which are not supported yet. Read / program 4 pages in one go. * - * $Id: nand_base.c,v 1.126 2004/12/13 11:22:25 lavinen Exp $ + * $Id: nand_base.c,v 1.147 2005/07/15 07:18:06 gleixner Exp $ * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License version 2 as @@ -149,17 +167,21 @@ static void nand_release_device (struct mtd_info *mtd) /* De-select the NAND device */ this->select_chip(mtd, -1); - /* Do we have a hardware controller ? */ + if (this->controller) { + /* Release the controller and the chip */ spin_lock(&this->controller->lock); this->controller->active = NULL; + this->state = FL_READY; + wake_up(&this->controller->wq); spin_unlock(&this->controller->lock); + } else { + /* Release the chip */ + spin_lock(&this->chip_lock); + this->state = FL_READY; + wake_up(&this->wq); + spin_unlock(&this->chip_lock); } - /* Release the chip */ - spin_lock (&this->chip_lock); - this->state = FL_READY; - wake_up (&this->wq); - spin_unlock (&this->chip_lock); } /** @@ -443,7 +465,8 @@ static int nand_default_block_markbad(struct mtd_info *mtd, loff_t ofs) /* Get block number */ block = ((int) ofs) >> this->bbt_erase_shift; - this->bbt[block >> 2] |= 0x01 << ((block & 0x03) << 1); + if (this->bbt) + this->bbt[block >> 2] |= 0x01 << ((block & 0x03) << 1); /* Do we have a flash based bad block table ? */ if (this->options & NAND_USE_FLASH_BBT) @@ -466,7 +489,7 @@ static int nand_check_wp (struct mtd_info *mtd) struct nand_chip *this = mtd->priv; /* Check the WP bit */ this->cmdfunc (mtd, NAND_CMD_STATUS, -1, -1); - return (this->read_byte(mtd) & 0x80) ? 0 : 1; + return (this->read_byte(mtd) & NAND_STATUS_WP) ? 0 : 1; } /** @@ -490,6 +513,22 @@ static int nand_block_checkbad (struct mtd_info *mtd, loff_t ofs, int getchip, i return nand_isbad_bbt (mtd, ofs, allowbbt); } +/* + * Wait for the ready pin, after a command + * The timeout is catched later. + */ +static void nand_wait_ready(struct mtd_info *mtd) +{ + struct nand_chip *this = mtd->priv; + unsigned long timeo = jiffies + 2; + + /* wait until command is processed or timeout occures */ + do { + if (this->dev_ready(mtd)) + return; + } while (time_before(jiffies, timeo)); +} + /** * nand_command - [DEFAULT] Send command to NAND device * @mtd: MTD device structure @@ -571,7 +610,7 @@ static void nand_command (struct mtd_info *mtd, unsigned command, int column, in this->hwcontrol(mtd, NAND_CTL_SETCLE); this->write_byte(mtd, NAND_CMD_STATUS); this->hwcontrol(mtd, NAND_CTL_CLRCLE); - while ( !(this->read_byte(mtd) & 0x40)); + while ( !(this->read_byte(mtd) & NAND_STATUS_READY)); return; /* This applies to read commands */ @@ -585,12 +624,11 @@ static void nand_command (struct mtd_info *mtd, unsigned command, int column, in return; } } - /* Apply this short delay always to ensure that we do wait tWB in * any case on any machine. */ ndelay (100); - /* wait until command is processed */ - while (!this->dev_ready(mtd)); + + nand_wait_ready(mtd); } /** @@ -619,7 +657,7 @@ static void nand_command_lp (struct mtd_info *mtd, unsigned command, int column, /* Begin command latch cycle */ this->hwcontrol(mtd, NAND_CTL_SETCLE); /* Write out the command to the device. */ - this->write_byte(mtd, command); + this->write_byte(mtd, (command & 0xff)); /* End command latch cycle */ this->hwcontrol(mtd, NAND_CTL_CLRCLE); @@ -647,8 +685,8 @@ static void nand_command_lp (struct mtd_info *mtd, unsigned command, int column, /* * program and erase have their own busy handlers - * status and sequential in needs no delay - */ + * status, sequential in, and deplete1 need no delay + */ switch (command) { case NAND_CMD_CACHEDPROG: @@ -657,8 +695,19 @@ static void nand_command_lp (struct mtd_info *mtd, unsigned command, int column, case NAND_CMD_ERASE2: case NAND_CMD_SEQIN: case NAND_CMD_STATUS: + case NAND_CMD_DEPLETE1: return; + /* + * read error status commands require only a short delay + */ + case NAND_CMD_STATUS_ERROR: + case NAND_CMD_STATUS_ERROR0: + case NAND_CMD_STATUS_ERROR1: + case NAND_CMD_STATUS_ERROR2: + case NAND_CMD_STATUS_ERROR3: + udelay(this->chip_delay); + return; case NAND_CMD_RESET: if (this->dev_ready) @@ -667,7 +716,7 @@ static void nand_command_lp (struct mtd_info *mtd, unsigned command, int column, this->hwcontrol(mtd, NAND_CTL_SETCLE); this->write_byte(mtd, NAND_CMD_STATUS); this->hwcontrol(mtd, NAND_CTL_CLRCLE); - while ( !(this->read_byte(mtd) & 0x40)); + while ( !(this->read_byte(mtd) & NAND_STATUS_READY)); return; case NAND_CMD_READ0: @@ -690,12 +739,12 @@ static void nand_command_lp (struct mtd_info *mtd, unsigned command, int column, return; } } - + /* Apply this short delay always to ensure that we do wait tWB in * any case on any machine. */ ndelay (100); - /* wait until command is processed */ - while (!this->dev_ready(mtd)); + + nand_wait_ready(mtd); } /** @@ -708,37 +757,34 @@ static void nand_command_lp (struct mtd_info *mtd, unsigned command, int column, */ static void nand_get_device (struct nand_chip *this, struct mtd_info *mtd, int new_state) { - struct nand_chip *active = this; - + struct nand_chip *active; + spinlock_t *lock; + wait_queue_head_t *wq; DECLARE_WAITQUEUE (wait, current); - /* - * Grab the lock and see if the device is available - */ + lock = (this->controller) ? &this->controller->lock : &this->chip_lock; + wq = (this->controller) ? &this->controller->wq : &this->wq; retry: + active = this; + spin_lock(lock); + /* Hardware controller shared among independend devices */ if (this->controller) { - spin_lock (&this->controller->lock); if (this->controller->active) active = this->controller->active; else this->controller->active = this; - spin_unlock (&this->controller->lock); } - - if (active == this) { - spin_lock (&this->chip_lock); - if (this->state == FL_READY) { - this->state = new_state; - spin_unlock (&this->chip_lock); - return; - } - } - set_current_state (TASK_UNINTERRUPTIBLE); - add_wait_queue (&active->wq, &wait); - spin_unlock (&active->chip_lock); - schedule (); - remove_wait_queue (&active->wq, &wait); + if (active == this && this->state == FL_READY) { + this->state = new_state; + spin_unlock(lock); + return; + } + set_current_state(TASK_UNINTERRUPTIBLE); + add_wait_queue(wq, &wait); + spin_unlock(lock); + schedule(); + remove_wait_queue(wq, &wait); goto retry; } @@ -785,7 +831,7 @@ static int nand_wait(struct mtd_info *mtd, struct nand_chip *this, int state) if (this->read_byte(mtd) & NAND_STATUS_READY) break; } - yield (); + cond_resched(); } status = (int) this->read_byte(mtd); return status; @@ -871,8 +917,14 @@ static int nand_write_page (struct mtd_info *mtd, struct nand_chip *this, int pa if (!cached) { /* call wait ready function */ status = this->waitfunc (mtd, this, FL_WRITING); + + /* See if operation failed and additional status checks are available */ + if ((status & NAND_STATUS_FAIL) && (this->errstat)) { + status = this->errstat(mtd, this, FL_WRITING, status, page); + } + /* See if device thinks it succeeded */ - if (status & 0x01) { + if (status & NAND_STATUS_FAIL) { DEBUG (MTD_DEBUG_LEVEL0, "%s: " "Failed write, page 0x%08x, ", __FUNCTION__, page); return -EIO; } @@ -975,7 +1027,7 @@ static int nand_verify_pages (struct mtd_info *mtd, struct nand_chip *this, int if (!this->dev_ready) udelay (this->chip_delay); else - while (!this->dev_ready(mtd)); + nand_wait_ready(mtd); /* All done, return happy */ if (!numpages) @@ -997,23 +1049,24 @@ out: #endif /** - * nand_read - [MTD Interface] MTD compability function for nand_read_ecc + * nand_read - [MTD Interface] MTD compability function for nand_do_read_ecc * @mtd: MTD device structure * @from: offset to read from * @len: number of bytes to read * @retlen: pointer to variable to store the number of read bytes * @buf: the databuffer to put data * - * This function simply calls nand_read_ecc with oob buffer and oobsel = NULL -*/ + * This function simply calls nand_do_read_ecc with oob buffer and oobsel = NULL + * and flags = 0xff + */ static int nand_read (struct mtd_info *mtd, loff_t from, size_t len, size_t * retlen, u_char * buf) { - return nand_read_ecc (mtd, from, len, retlen, buf, NULL, NULL); -} + return nand_do_read_ecc (mtd, from, len, retlen, buf, NULL, &mtd->oobinfo, 0xff); +} /** - * nand_read_ecc - [MTD Interface] Read data with ECC + * nand_read_ecc - [MTD Interface] MTD compability function for nand_do_read_ecc * @mtd: MTD device structure * @from: offset to read from * @len: number of bytes to read @@ -1022,11 +1075,39 @@ static int nand_read (struct mtd_info *mtd, loff_t from, size_t len, size_t * re * @oob_buf: filesystem supplied oob data buffer * @oobsel: oob selection structure * - * NAND read with ECC + * This function simply calls nand_do_read_ecc with flags = 0xff */ static int nand_read_ecc (struct mtd_info *mtd, loff_t from, size_t len, size_t * retlen, u_char * buf, u_char * oob_buf, struct nand_oobinfo *oobsel) { + /* use userspace supplied oobinfo, if zero */ + if (oobsel == NULL) + oobsel = &mtd->oobinfo; + return nand_do_read_ecc(mtd, from, len, retlen, buf, oob_buf, oobsel, 0xff); +} + + +/** + * nand_do_read_ecc - [MTD Interface] Read data with ECC + * @mtd: MTD device structure + * @from: offset to read from + * @len: number of bytes to read + * @retlen: pointer to variable to store the number of read bytes + * @buf: the databuffer to put data + * @oob_buf: filesystem supplied oob data buffer (can be NULL) + * @oobsel: oob selection structure + * @flags: flag to indicate if nand_get_device/nand_release_device should be preformed + * and how many corrected error bits are acceptable: + * bits 0..7 - number of tolerable errors + * bit 8 - 0 == do not get/release chip, 1 == get/release chip + * + * NAND read with ECC + */ +int nand_do_read_ecc (struct mtd_info *mtd, loff_t from, size_t len, + size_t * retlen, u_char * buf, u_char * oob_buf, + struct nand_oobinfo *oobsel, int flags) +{ + int i, j, col, realpage, page, end, ecc, chipnr, sndcmd = 1; int read = 0, oob = 0, ecc_status = 0, ecc_failed = 0; struct nand_chip *this = mtd->priv; @@ -1051,12 +1132,9 @@ static int nand_read_ecc (struct mtd_info *mtd, loff_t from, size_t len, } /* Grab the lock and see if the device is available */ - nand_get_device (this, mtd ,FL_READING); + if (flags & NAND_GET_DEVICE) + nand_get_device (this, mtd, FL_READING); - /* use userspace supplied oobinfo, if zero */ - if (oobsel == NULL) - oobsel = &mtd->oobinfo; - /* Autoplace of oob data ? Use the default placement scheme */ if (oobsel->useecc == MTD_NANDECC_AUTOPLACE) oobsel = this->autooob; @@ -1118,7 +1196,8 @@ static int nand_read_ecc (struct mtd_info *mtd, loff_t from, size_t len, } /* get oob area, if we have no oob buffer from fs-driver */ - if (!oob_buf || oobsel->useecc == MTD_NANDECC_AUTOPLACE) + if (!oob_buf || oobsel->useecc == MTD_NANDECC_AUTOPLACE || + oobsel->useecc == MTD_NANDECC_AUTOPL_USR) oob_data = &this->data_buf[end]; eccsteps = this->eccsteps; @@ -1155,7 +1234,8 @@ static int nand_read_ecc (struct mtd_info *mtd, loff_t from, size_t len, /* We calc error correction directly, it checks the hw * generator for an error, reads back the syndrome and * does the error correction on the fly */ - if (this->correct_data(mtd, &data_poi[datidx], &oob_data[i], &ecc_code[i]) == -1) { + ecc_status = this->correct_data(mtd, &data_poi[datidx], &oob_data[i], &ecc_code[i]); + if ((ecc_status == -1) || (ecc_status > (flags && 0xff))) { DEBUG (MTD_DEBUG_LEVEL0, "nand_read_ecc: " "Failed ECC read, page 0x%08x on chip %d\n", page, chipnr); ecc_failed++; @@ -1194,7 +1274,7 @@ static int nand_read_ecc (struct mtd_info *mtd, loff_t from, size_t len, p[i] = ecc_status; } - if (ecc_status == -1) { + if ((ecc_status == -1) || (ecc_status > (flags && 0xff))) { DEBUG (MTD_DEBUG_LEVEL0, "nand_read_ecc: " "Failed ECC read, page 0x%08x\n", page); ecc_failed++; } @@ -1206,14 +1286,14 @@ static int nand_read_ecc (struct mtd_info *mtd, loff_t from, size_t len, /* without autoplace. Legacy mode used by YAFFS1 */ switch(oobsel->useecc) { case MTD_NANDECC_AUTOPLACE: + case MTD_NANDECC_AUTOPL_USR: /* Walk through the autoplace chunks */ - for (i = 0, j = 0; j < mtd->oobavail; i++) { + for (i = 0; oobsel->oobfree[i][1]; i++) { int from = oobsel->oobfree[i][0]; int num = oobsel->oobfree[i][1]; memcpy(&oob_buf[oob], &oob_data[from], num); - j+= num; + oob += num; } - oob += mtd->oobavail; break; case MTD_NANDECC_PLACE: /* YAFFS1 legacy mode */ @@ -1239,7 +1319,7 @@ static int nand_read_ecc (struct mtd_info *mtd, loff_t from, size_t len, if (!this->dev_ready) udelay (this->chip_delay); else - while (!this->dev_ready(mtd)); + nand_wait_ready(mtd); if (read == len) break; @@ -1264,7 +1344,8 @@ static int nand_read_ecc (struct mtd_info *mtd, loff_t from, size_t len, } /* Deselect and wake up anyone waiting on the device */ - nand_release_device(mtd); + if (flags & NAND_GET_DEVICE) + nand_release_device(mtd); /* * Return success, if no ECC failures, else -EBADMSG @@ -1328,16 +1409,6 @@ static int nand_read_oob (struct mtd_info *mtd, loff_t from, size_t len, size_t thislen = min_t(int, thislen, len); this->read_buf(mtd, &buf[i], thislen); i += thislen; - - /* Apply delay or wait for ready/busy pin - * Do this before the AUTOINCR check, so no problems - * arise if a chip which does auto increment - * is marked as NOAUTOINCR by the board driver. - */ - if (!this->dev_ready) - udelay (this->chip_delay); - else - while (!this->dev_ready(mtd)); /* Read more ? */ if (i < len) { @@ -1351,6 +1422,16 @@ static int nand_read_oob (struct mtd_info *mtd, loff_t from, size_t len, size_t this->select_chip(mtd, chipnr); } + /* Apply delay or wait for ready/busy pin + * Do this before the AUTOINCR check, so no problems + * arise if a chip which does auto increment + * is marked as NOAUTOINCR by the board driver. + */ + if (!this->dev_ready) + udelay (this->chip_delay); + else + nand_wait_ready(mtd); + /* Check, if the chip supports auto page increment * or if we have hit a block boundary. */ @@ -1417,7 +1498,7 @@ int nand_read_raw (struct mtd_info *mtd, uint8_t *buf, loff_t from, size_t len, if (!this->dev_ready) udelay (this->chip_delay); else - while (!this->dev_ready(mtd)); + nand_wait_ready(mtd); /* Check, if the chip supports auto page increment */ if (!NAND_CANAUTOINCR(this) || !(page & blockcheck)) @@ -1567,6 +1648,8 @@ static int nand_write_ecc (struct mtd_info *mtd, loff_t to, size_t len, oobsel = this->autooob; autoplace = 1; } + if (oobsel->useecc == MTD_NANDECC_AUTOPL_USR) + autoplace = 1; /* Setup variables and oob buffer */ totalpages = len >> this->page_shift; @@ -1733,7 +1816,7 @@ static int nand_write_oob (struct mtd_info *mtd, loff_t to, size_t len, size_t * status = this->waitfunc (mtd, this, FL_WRITING); /* See if device thinks it succeeded */ - if (status & 0x01) { + if (status & NAND_STATUS_FAIL) { DEBUG (MTD_DEBUG_LEVEL0, "nand_write_oob: " "Failed write, page 0x%08x\n", page); ret = -EIO; goto out; @@ -1841,6 +1924,8 @@ static int nand_writev_ecc (struct mtd_info *mtd, const struct kvec *vecs, unsig oobsel = this->autooob; autoplace = 1; } + if (oobsel->useecc == MTD_NANDECC_AUTOPL_USR) + autoplace = 1; /* Setup start page */ page = (int) (to >> this->page_shift); @@ -1987,6 +2072,7 @@ static int nand_erase (struct mtd_info *mtd, struct erase_info *instr) return nand_erase_nand (mtd, instr, 0); } +#define BBT_PAGE_MASK 0xffffff3f /** * nand_erase_intern - [NAND Interface] erase block(s) * @mtd: MTD device structure @@ -1999,6 +2085,10 @@ int nand_erase_nand (struct mtd_info *mtd, struct erase_info *instr, int allowbb { int page, len, status, pages_per_block, ret, chipnr; struct nand_chip *this = mtd->priv; + int rewrite_bbt[NAND_MAX_CHIPS]={0}; /* flags to indicate the page, if bbt needs to be rewritten. */ + unsigned int bbt_masked_page; /* bbt mask to compare to page being erased. */ + /* It is used to see if the current page is in the same */ + /* 256 block group and the same bank as the bbt. */ DEBUG (MTD_DEBUG_LEVEL3, "nand_erase: start = 0x%08x, len = %i\n", (unsigned int) instr->addr, (unsigned int) instr->len); @@ -2044,6 +2134,13 @@ int nand_erase_nand (struct mtd_info *mtd, struct erase_info *instr, int allowbb goto erase_exit; } + /* if BBT requires refresh, set the BBT page mask to see if the BBT should be rewritten */ + if (this->options & BBT_AUTO_REFRESH) { + bbt_masked_page = this->bbt_td->pages[chipnr] & BBT_PAGE_MASK; + } else { + bbt_masked_page = 0xffffffff; /* should not match anything */ + } + /* Loop through the pages */ len = instr->len; @@ -2066,13 +2163,26 @@ int nand_erase_nand (struct mtd_info *mtd, struct erase_info *instr, int allowbb status = this->waitfunc (mtd, this, FL_ERASING); + /* See if operation failed and additional status checks are available */ + if ((status & NAND_STATUS_FAIL) && (this->errstat)) { + status = this->errstat(mtd, this, FL_ERASING, status, page); + } + /* See if block erase succeeded */ - if (status & 0x01) { + if (status & NAND_STATUS_FAIL) { DEBUG (MTD_DEBUG_LEVEL0, "nand_erase: " "Failed erase, page 0x%08x\n", page); instr->state = MTD_ERASE_FAILED; instr->fail_addr = (page << this->page_shift); goto erase_exit; } + + /* if BBT requires refresh, set the BBT rewrite flag to the page being erased */ + if (this->options & BBT_AUTO_REFRESH) { + if (((page & BBT_PAGE_MASK) == bbt_masked_page) && + (page != this->bbt_td->pages[chipnr])) { + rewrite_bbt[chipnr] = (page << this->page_shift); + } + } /* Increment page address and decrement length */ len -= (1 << this->phys_erase_shift); @@ -2083,6 +2193,13 @@ int nand_erase_nand (struct mtd_info *mtd, struct erase_info *instr, int allowbb chipnr++; this->select_chip(mtd, -1); this->select_chip(mtd, chipnr); + + /* if BBT requires refresh and BBT-PERCHIP, + * set the BBT page mask to see if this BBT should be rewritten */ + if ((this->options & BBT_AUTO_REFRESH) && (this->bbt_td->options & NAND_BBT_PERCHIP)) { + bbt_masked_page = this->bbt_td->pages[chipnr] & BBT_PAGE_MASK; + } + } } instr->state = MTD_ERASE_DONE; @@ -2097,6 +2214,18 @@ erase_exit: /* Deselect and wake up anyone waiting on the device */ nand_release_device(mtd); + /* if BBT requires refresh and erase was successful, rewrite any selected bad block tables */ + if ((this->options & BBT_AUTO_REFRESH) && (!ret)) { + for (chipnr = 0; chipnr < this->numchips; chipnr++) { + if (rewrite_bbt[chipnr]) { + /* update the BBT for chip */ + DEBUG (MTD_DEBUG_LEVEL0, "nand_erase_nand: nand_update_bbt (%d:0x%0x 0x%0x)\n", + chipnr, rewrite_bbt[chipnr], this->bbt_td->pages[chipnr]); + nand_update_bbt (mtd, rewrite_bbt[chipnr]); + } + } + } + /* Return more or less happy */ return ret; } @@ -2168,7 +2297,7 @@ static int nand_block_markbad (struct mtd_info *mtd, loff_t ofs) */ int nand_scan (struct mtd_info *mtd, int maxchips) { - int i, j, nand_maf_id, nand_dev_id, busw; + int i, nand_maf_id, nand_dev_id, busw, maf_id; struct nand_chip *this = mtd->priv; /* Get buswidth to select the correct functions*/ @@ -2256,12 +2385,18 @@ int nand_scan (struct mtd_info *mtd, int maxchips) busw = nand_flash_ids[i].options & NAND_BUSWIDTH_16; } + /* Try to identify manufacturer */ + for (maf_id = 0; nand_manuf_ids[maf_id].id != 0x0; maf_id++) { + if (nand_manuf_ids[maf_id].id == nand_maf_id) + break; + } + /* Check, if buswidth is correct. Hardware drivers should set * this correct ! */ if (busw != (this->options & NAND_BUSWIDTH_16)) { printk (KERN_INFO "NAND device: Manufacturer ID:" " 0x%02x, Chip ID: 0x%02x (%s %s)\n", nand_maf_id, nand_dev_id, - nand_manuf_ids[i].name , mtd->name); + nand_manuf_ids[maf_id].name , mtd->name); printk (KERN_WARNING "NAND bus width %d instead %d bit\n", (this->options & NAND_BUSWIDTH_16) ? 16 : 8, @@ -2300,14 +2435,9 @@ int nand_scan (struct mtd_info *mtd, int maxchips) if (mtd->oobblock > 512 && this->cmdfunc == nand_command) this->cmdfunc = nand_command_lp; - /* Try to identify manufacturer */ - for (j = 0; nand_manuf_ids[j].id != 0x0; j++) { - if (nand_manuf_ids[j].id == nand_maf_id) - break; - } printk (KERN_INFO "NAND device: Manufacturer ID:" " 0x%02x, Chip ID: 0x%02x (%s %s)\n", nand_maf_id, nand_dev_id, - nand_manuf_ids[j].name , nand_flash_ids[i].name); + nand_manuf_ids[maf_id].name , nand_flash_ids[i].name); break; } @@ -2388,12 +2518,9 @@ int nand_scan (struct mtd_info *mtd, int maxchips) /* The number of bytes available for the filesystem to place fs dependend * oob data */ - if (this->options & NAND_BUSWIDTH_16) { - mtd->oobavail = mtd->oobsize - (this->autooob->eccbytes + 2); - if (this->autooob->eccbytes & 0x01) - mtd->oobavail--; - } else - mtd->oobavail = mtd->oobsize - (this->autooob->eccbytes + 1); + mtd->oobavail = 0; + for (i = 0; this->autooob->oobfree[i][1]; i++) + mtd->oobavail += this->autooob->oobfree[i][1]; /* * check ECC mode, default to software @@ -2524,6 +2651,10 @@ int nand_scan (struct mtd_info *mtd, int maxchips) memcpy(&mtd->oobinfo, this->autooob, sizeof(mtd->oobinfo)); mtd->owner = THIS_MODULE; + + /* Check, if we should skip the bad block table scan */ + if (this->options & NAND_SKIP_BBTSCAN) + return 0; /* Build bad block table */ return this->scan_bbt (mtd); @@ -2555,8 +2686,8 @@ void nand_release (struct mtd_info *mtd) kfree (this->data_buf); } -EXPORT_SYMBOL (nand_scan); -EXPORT_SYMBOL (nand_release); +EXPORT_SYMBOL_GPL (nand_scan); +EXPORT_SYMBOL_GPL (nand_release); MODULE_LICENSE ("GPL"); MODULE_AUTHOR ("Steven J. Hill <sjhill@realitydiluted.com>, Thomas Gleixner <tglx@linutronix.de>"); |