diff options
Diffstat (limited to 'include/asm-arm/arch-mxc/board-mx27ads.h')
| -rw-r--r-- | include/asm-arm/arch-mxc/board-mx27ads.h | 354 |
1 files changed, 354 insertions, 0 deletions
diff --git a/include/asm-arm/arch-mxc/board-mx27ads.h b/include/asm-arm/arch-mxc/board-mx27ads.h new file mode 100644 index 0000000..61e66da --- /dev/null +++ b/include/asm-arm/arch-mxc/board-mx27ads.h @@ -0,0 +1,354 @@ +/* + * Copyright 2005-2007 Freescale Semiconductor, Inc. All Rights Reserved. + */ + +/* + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +#ifndef __ASM_ARCH_MXC_BOARD_MX27ADS_H__ +#define __ASM_ARCH_MXC_BOARD_MX27ADS_H__ + +/* external interrupt multiplexer */ +#define MXC_EXP_IO_BASE (MXC_GPIO_BASE + MXC_MAX_GPIO_LINES) + +#define MXC_VIRTUAL_INTS_BASE (MXC_EXP_IO_BASE + MXC_MAX_EXP_IO_LINES) +#define MXC_SDIO1_CARD_IRQ MXC_VIRTUAL_INTS_BASE +#define MXC_SDIO2_CARD_IRQ (MXC_VIRTUAL_INTS_BASE + 1) +#define MXC_SDIO3_CARD_IRQ (MXC_VIRTUAL_INTS_BASE + 2) + +#define MXC_MAX_BOARD_INTS (MXC_MAX_EXP_IO_LINES + \ + MXC_MAX_VIRTUAL_INTS) + +/* + * MXC UART EVB board level configurations + */ + +#define MXC_LL_EXTUART_PADDR (CS4_BASE_ADDR + 0x20000) +#define MXC_LL_EXTUART_VADDR (CS4_BASE_ADDR_VIRT + 0x20000) +#define MXC_LL_EXTUART_16BIT_BUS + +#define MXC_LL_UART_PADDR UART1_BASE_ADDR +#define MXC_LL_UART_VADDR AIPI_IO_ADDRESS(UART1_BASE_ADDR) + +/* + * @name Memory Size parameters + */ + +/* + * Size of SDRAM memory + */ +#define SDRAM_MEM_SIZE SZ_128M + +/* + * PBC Controller parameters + */ + +/* + * Base address of PBC controller, CS4 + */ +#define PBC_BASE_ADDRESS 0xEB000000 +#define PBC_REG_ADDR(offset) (PBC_BASE_ADDRESS + (offset)) + +/* + * PBC Interupt name definitions + */ +#define PBC_GPIO1_0 0 +#define PBC_GPIO1_1 1 +#define PBC_GPIO1_2 2 +#define PBC_GPIO1_3 3 +#define PBC_GPIO1_4 4 +#define PBC_GPIO1_5 5 + +#define PBC_INTR_MAX_NUM 6 +#define PBC_INTR_SHARED_MAX_NUM 8 + +/* When the PBC address connection is fixed in h/w, defined as 1 */ +#define PBC_ADDR_SH 0 + +/* Offsets for the PBC Controller register */ +/* + * PBC Board version register offset + */ +#define PBC_VERSION_REG PBC_REG_ADDR(0x00000 >> PBC_ADDR_SH) +/* + * PBC Board control register 1 set address. + */ +#define PBC_BCTRL1_SET_REG PBC_REG_ADDR(0x00008 >> PBC_ADDR_SH) +/* + * PBC Board control register 1 clear address. + */ +#define PBC_BCTRL1_CLEAR_REG PBC_REG_ADDR(0x0000C >> PBC_ADDR_SH) +/* + * PBC Board control register 2 set address. + */ +#define PBC_BCTRL2_SET_REG PBC_REG_ADDR(0x00010 >> PBC_ADDR_SH) +/* + * PBC Board control register 2 clear address. + */ +#define PBC_BCTRL2_CLEAR_REG PBC_REG_ADDR(0x00014 >> PBC_ADDR_SH) +/* + * PBC Board control register 3 set address. + */ +#define PBC_BCTRL3_SET_REG PBC_REG_ADDR(0x00018 >> PBC_ADDR_SH) +/* + * PBC Board control register 3 clear address. + */ +#define PBC_BCTRL3_CLEAR_REG PBC_REG_ADDR(0x0001C >> PBC_ADDR_SH) +/* + * PBC Board control register 3 set address. + */ +#define PBC_BCTRL4_SET_REG PBC_REG_ADDR(0x00020 >> PBC_ADDR_SH) +/* + * PBC Board control register 4 clear address. + */ +#define PBC_BCTRL4_CLEAR_REG PBC_REG_ADDR(0x00024 >> PBC_ADDR_SH) +/*PBC_ADDR_SH + * PBC Board status register 1. + */ +#define PBC_BSTAT1_REG PBC_REG_ADDR(0x00028 >> PBC_ADDR_SH) +/* + * PBC Board interrupt status register. + */ +#define PBC_INTSTATUS_REG PBC_REG_ADDR(0x0002C >> PBC_ADDR_SH) +/* + * PBC Board interrupt current status register. + */ +#define PBC_INTCURR_STATUS_REG PBC_REG_ADDR(0x00034 >> PBC_ADDR_SH) +/* + * PBC Interrupt mask register set address. + */ +#define PBC_INTMASK_SET_REG PBC_REG_ADDR(0x00038 >> PBC_ADDR_SH) +/* + * PBC Interrupt mask register clear address. + */ +#define PBC_INTMASK_CLEAR_REG PBC_REG_ADDR(0x0003C >> PBC_ADDR_SH) +/* + * External UART A. + */ +#define PBC_SC16C652_UARTA_REG PBC_REG_ADDR(0x20000 >> PBC_ADDR_SH) +/* + * UART 4 Expanding Signal Status. + */ +#define PBC_UART_STATUS_REG PBC_REG_ADDR(0x22000 >> PBC_ADDR_SH) +/* + * UART 4 Expanding Signal Control Set. + */ +#define PBC_UCTRL_SET_REG PBC_REG_ADDR(0x24000 >> PBC_ADDR_SH) +/* + * UART 4 Expanding Signal Control Clear. + */ +#define PBC_UCTRL_CLR_REG PBC_REG_ADDR(0x26000 >> PBC_ADDR_SH) +/* + * Ethernet Controller IO base address. + */ +#define PBC_CS8900A_IOBASE_REG PBC_REG_ADDR(0x40000 >> PBC_ADDR_SH) +/* + * Ethernet Controller Memory base address. + */ +#define PBC_CS8900A_MEMBASE_REG PBC_REG_ADDR(0x42000 >> PBC_ADDR_SH) +/* + * Ethernet Controller DMA base address. + */ +#define PBC_CS8900A_DMABASE_REG PBC_REG_ADDR(0x44000 >> PBC_ADDR_SH) + +/* PBC Board Version Register bit definition */ +#define PBC_VERSION_ADS 0x8000 /* Bit15=1 means version for ads */ +#define PBC_VERSION_EVB_REVB 0x4000 /* BIT14=1 means version for evb revb */ + +/* PBC Board Control Register 1 bit definitions */ +#define PBC_BCTRL1_ERST 0x0001 /* Ethernet Reset */ +#define PBC_BCTRL1_URST 0x0002 /* Reset External UART controller */ +#define PBC_BCTRL1_FRST 0x0004 /* FEC Reset */ +#define PBC_BCTRL1_ESLEEP 0x0010 /* Enable ethernet Sleep */ +#define PBC_BCTRL1_LCDON 0x0800 /* Enable the LCD */ + +/* PBC Board Control Register 2 bit definitions */ +#define PBC_BCTRL2_VCC_EN 0x0004 /* Enable VCC */ +#define PBC_BCTRL2_VPP_EN 0x0008 /* Enable Vpp */ +#define PBC_BCTRL2_ATAFEC_EN 0X0010 +#define PBC_BCTRL2_ATAFEC_SEL 0X0020 +#define PBC_BCTRL2_ATA_EN 0X0040 +#define PBC_BCTRL2_IRDA_SD 0X0080 +#define PBC_BCTRL2_IRDA_EN 0X0100 +#define PBC_BCTRL2_CCTL10 0X0200 +#define PBC_BCTRL2_CCTL11 0X0400 + +/* PBC Board Control Register 3 bit definitions */ +#define PBC_BCTRL3_HSH_EN 0X0020 +#define PBC_BCTRL3_FSH_MOD 0X0040 +#define PBC_BCTRL3_OTG_HS_EN 0X0080 +#define PBC_BCTRL3_OTG_VBUS_EN 0X0100 +#define PBC_BCTRL3_FSH_VBUS_EN 0X0200 +#define PBC_BCTRL3_USB_OTG_ON 0X0800 +#define PBC_BCTRL3_USB_FSH_ON 0X1000 + +/* PBC Board Control Register 4 bit definitions */ +#define PBC_BCTRL4_REGEN_SEL 0X0001 +#define PBC_BCTRL4_USER_OFF 0X0002 +#define PBC_BCTRL4_VIB_EN 0X0004 +#define PBC_BCTRL4_PWRGT1_EN 0X0008 +#define PBC_BCTRL4_PWRGT2_EN 0X0010 +#define PBC_BCTRL4_STDBY_PRI 0X0020 + +#ifndef __ASSEMBLY__ +/* + * Enumerations for SD cards and memory stick card. This corresponds to + * the card EN bits in the IMR: SD1_EN | MS_EN | SD3_EN | SD2_EN. + */ +enum mxc_card_no { + MXC_CARD_SD2 = 0, + MXC_CARD_SD3, + MXC_CARD_MS, + MXC_CARD_SD1, + MXC_CARD_MIN = MXC_CARD_SD2, + MXC_CARD_MAX = MXC_CARD_SD1, +}; +#endif + +#define MXC_CPLD_VER_1_50 0x01 + +/* + * PBC BSTAT Register bit definitions + */ +#define PBC_BSTAT_PRI_INT 0X0001 +#define PBC_BSTAT_USB_BYP 0X0002 +#define PBC_BSTAT_ATA_IOCS16 0X0004 +#define PBC_BSTAT_ATA_CBLID 0X0008 +#define PBC_BSTAT_ATA_DASP 0X0010 +#define PBC_BSTAT_PWR_RDY 0X0020 +#define PBC_BSTAT_SD3_WP 0X0100 +#define PBC_BSTAT_SD2_WP 0X0200 +#define PBC_BSTAT_SD1_WP 0X0400 +#define PBC_BSTAT_SD3_DET 0X0800 +#define PBC_BSTAT_SD2_DET 0X1000 +#define PBC_BSTAT_SD1_DET 0X2000 +#define PBC_BSTAT_MS_DET 0X4000 +#define PBC_BSTAT_SD3_DET_BIT 11 +#define PBC_BSTAT_SD2_DET_BIT 12 +#define PBC_BSTAT_SD1_DET_BIT 13 +#define PBC_BSTAT_MS_DET_BIT 14 +#define MXC_BSTAT_BIT(n) ((n == MXC_CARD_SD2) ? PBC_BSTAT_SD2_DET : \ + ((n == MXC_CARD_SD3) ? PBC_BSTAT_SD3_DET : \ + ((n == MXC_CARD_SD1) ? PBC_BSTAT_SD1_DET : \ + ((n == MXC_CARD_MS) ? PBC_BSTAT_MS_DET : \ + 0x0)))) + +/* + * PBC UART Control Register bit definitions + */ +#define PBC_UCTRL_DCE_DCD 0X0001 +#define PBC_UCTRL_DCE_DSR 0X0002 +#define PBC_UCTRL_DCE_RI 0X0004 +#define PBC_UCTRL_DTE_DTR 0X0100 + +/* + * PBC UART Status Register bit definitions + */ +#define PBC_USTAT_DTE_DCD 0X0001 +#define PBC_USTAT_DTE_DSR 0X0002 +#define PBC_USTAT_DTE_RI 0X0004 +#define PBC_USTAT_DCE_DTR 0X0100 + +/* + * PBC Interupt mask register bit definitions + */ +#define PBC_INTR_SD3_R_EN_BIT 4 +#define PBC_INTR_SD2_R_EN_BIT 0 +#define PBC_INTR_SD1_R_EN_BIT 6 +#define PBC_INTR_MS_R_EN_BIT 5 +#define PBC_INTR_SD3_EN_BIT 13 +#define PBC_INTR_SD2_EN_BIT 12 +#define PBC_INTR_MS_EN_BIT 14 +#define PBC_INTR_SD1_EN_BIT 15 + +#define PBC_INTR_SD2_R_EN 0x0001 +#define PBC_INTR_LOW_BAT 0X0002 +#define PBC_INTR_OTG_FSOVER 0X0004 +#define PBC_INTR_FSH_OVER 0X0008 +#define PBC_INTR_SD3_R_EN 0x0010 +#define PBC_INTR_MS_R_EN 0x0020 +#define PBC_INTR_SD1_R_EN 0x0040 +#define PBC_INTR_FEC_INT 0X0080 +#define PBC_INTR_ENET_INT 0X0100 +#define PBC_INTR_OTGFS_INT 0X0200 +#define PBC_INTR_XUART_INT 0X0400 +#define PBC_INTR_CCTL12 0X0800 +#define PBC_INTR_SD2_EN 0x1000 +#define PBC_INTR_SD3_EN 0x2000 +#define PBC_INTR_MS_EN 0x4000 +#define PBC_INTR_SD1_EN 0x8000 + + + +/* For interrupts like xuart, enet etc */ +#define EXPIO_PARENT_INT IOMUX_TO_IRQ(MX27_PIN_TIN) +#define MXC_MAX_EXP_IO_LINES 16 + +/* + * This corresponds to PBC_INTMASK_SET_REG at offset 0x38. + * + */ +#define EXPIO_INT_LOW_BAT (MXC_EXP_IO_BASE + 1) +#define EXPIO_INT_OTG_FS_OVR (MXC_EXP_IO_BASE + 2) +#define EXPIO_INT_FSH_OVR (MXC_EXP_IO_BASE + 3) +#define EXPIO_INT_RES4 (MXC_EXP_IO_BASE + 4) +#define EXPIO_INT_RES5 (MXC_EXP_IO_BASE + 5) +#define EXPIO_INT_RES6 (MXC_EXP_IO_BASE + 6) +#define EXPIO_INT_FEC (MXC_EXP_IO_BASE + 7) +#define EXPIO_INT_ENET_INT (MXC_EXP_IO_BASE + 8) +#define EXPIO_INT_OTG_FS_INT (MXC_EXP_IO_BASE + 9) +#define EXPIO_INT_XUART_INTA (MXC_EXP_IO_BASE + 10) +#define EXPIO_INT_CCTL12_INT (MXC_EXP_IO_BASE + 11) +#define EXPIO_INT_SD2_EN (MXC_EXP_IO_BASE + 12) +#define EXPIO_INT_SD3_EN (MXC_EXP_IO_BASE + 13) +#define EXPIO_INT_MS_EN (MXC_EXP_IO_BASE + 14) +#define EXPIO_INT_SD1_EN (MXC_EXP_IO_BASE + 15) + +/* + * This is System IRQ used by CS8900A for interrupt generation + * taken from platform.h + */ +#define CS8900AIRQ EXPIO_INT_ENET_INT +/* This is I/O Base address used to access registers of CS8900A on MXC ADS */ +#define CS8900A_BASE_ADDRESS (PBC_CS8900A_IOBASE_REG + 0x300) + +#define MXC_PMIC_INT_LINE IOMUX_TO_IRQ(MX27_PIN_TOUT) + +/* +* This is used to detect if the CPLD version is for mx27 evb board rev-a +*/ +#define PBC_CPLD_VERSION_IS_REVA() \ + ((__raw_readw(PBC_VERSION_REG) & \ + (PBC_VERSION_ADS | PBC_VERSION_EVB_REVB))\ + == 0) + +/* This is used to active or inactive ata signal in CPLD . + * It is dependent with hardware + */ +#define PBC_ATA_SIGNAL_ACTIVE() \ + __raw_writew( \ + PBC_BCTRL2_ATAFEC_EN|PBC_BCTRL2_ATAFEC_SEL|PBC_BCTRL2_ATA_EN, \ + PBC_BCTRL2_CLEAR_REG) + +#define PBC_ATA_SIGNAL_INACTIVE() \ + __raw_writew( \ + PBC_BCTRL2_ATAFEC_EN|PBC_BCTRL2_ATAFEC_SEL|PBC_BCTRL2_ATA_EN, \ + PBC_BCTRL2_SET_REG) + +#define MXC_BD_LED1 (1 << 5) +#define MXC_BD_LED2 (1 << 6) +#define MXC_BD_LED_ON(led) \ + __raw_writew(led, PBC_BCTRL1_SET_REG) +#define MXC_BD_LED_OFF(led) \ + __raw_writew(led, PBC_BCTRL1_CLEAR_REG) + +/* to determine the correct external crystal reference */ +#define CKIH_27MHZ_BIT_SET (1 << 3) + +#endif /* __ASM_ARCH_MXC_BOARD_MX27ADS_H__ */ |