1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
|
#undef DEBUG
#include <linux/kernel.h>
#include <linux/string.h>
#include <linux/pci_regs.h>
#include <linux/module.h>
#include <linux/ioport.h>
#include <linux/etherdevice.h>
#include <linux/of_address.h>
#include <asm/prom.h>
#include <asm/pci-bridge.h>
#ifdef CONFIG_PCI
int of_irq_map_pci(struct pci_dev *pdev, struct of_irq *out_irq)
{
struct device_node *dn, *ppnode;
struct pci_dev *ppdev;
u32 lspec;
u32 laddr[3];
u8 pin;
int rc;
/* Check if we have a device node, if yes, fallback to standard OF
* parsing
*/
dn = pci_device_to_OF_node(pdev);
if (dn) {
rc = of_irq_map_one(dn, 0, out_irq);
if (!rc)
return rc;
}
/* Ok, we don't, time to have fun. Let's start by building up an
* interrupt spec. we assume #interrupt-cells is 1, which is standard
* for PCI. If you do different, then don't use that routine.
*/
rc = pci_read_config_byte(pdev, PCI_INTERRUPT_PIN, &pin);
if (rc != 0)
return rc;
/* No pin, exit */
if (pin == 0)
return -ENODEV;
/* Now we walk up the PCI tree */
lspec = pin;
for (;;) {
/* Get the pci_dev of our parent */
ppdev = pdev->bus->self;
/* Ouch, it's a host bridge... */
if (ppdev == NULL) {
#ifdef CONFIG_PPC64
ppnode = pci_bus_to_OF_node(pdev->bus);
#else
struct pci_controller *host;
host = pci_bus_to_host(pdev->bus);
ppnode = host ? host->dn : NULL;
#endif
/* No node for host bridge ? give up */
if (ppnode == NULL)
return -EINVAL;
} else
/* We found a P2P bridge, check if it has a node */
ppnode = pci_device_to_OF_node(ppdev);
/* Ok, we have found a parent with a device-node, hand over to
* the OF parsing code.
* We build a unit address from the linux device to be used for
* resolution. Note that we use the linux bus number which may
* not match your firmware bus numbering.
* Fortunately, in most cases, interrupt-map-mask doesn't include
* the bus number as part of the matching.
* You should still be careful about that though if you intend
* to rely on this function (you ship a firmware that doesn't
* create device nodes for all PCI devices).
*/
if (ppnode)
break;
/* We can only get here if we hit a P2P bridge with no node,
* let's do standard swizzling and try again
*/
lspec = pci_swizzle_interrupt_pin(pdev, lspec);
pdev = ppdev;
}
laddr[0] = (pdev->bus->number << 16)
| (pdev->devfn << 8);
laddr[1] = laddr[2] = 0;
return of_irq_map_raw(ppnode, &lspec, 1, laddr, out_irq);
}
EXPORT_SYMBOL_GPL(of_irq_map_pci);
#endif /* CONFIG_PCI */
void of_parse_dma_window(struct device_node *dn, const void *dma_window_prop,
unsigned long *busno, unsigned long *phys, unsigned long *size)
{
const u32 *dma_window;
u32 cells;
const unsigned char *prop;
dma_window = dma_window_prop;
/* busno is always one cell */
*busno = *(dma_window++);
prop = of_get_property(dn, "ibm,#dma-address-cells", NULL);
if (!prop)
prop = of_get_property(dn, "#address-cells", NULL);
cells = prop ? *(u32 *)prop : of_n_addr_cells(dn);
*phys = of_read_number(dma_window, cells);
dma_window += cells;
prop = of_get_property(dn, "ibm,#dma-size-cells", NULL);
cells = prop ? *(u32 *)prop : of_n_size_cells(dn);
*size = of_read_number(dma_window, cells);
}
|
