hwmon: Add a driver for the ADT7475 hardware monitoring chip

Hwmon driver for the ADT7475 chip.

Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

4 files changed, 1320 insertions, 0 deletions

diff --git a/Documentation/hwmon/adt7475 b/Documentation/hwmon/adt7475
new file mode 100644
index 0000000..a2b1abe
--- /dev/null
+++ b/Documentation/hwmon/adt7475
@@ -0,0 +1,87 @@
+This describes the interface for the ADT7475 driver:
+
+(there are 4 fans, numbered fan1 to fan4):
+
+fanX_input		Read the current speed of the fan (in RPMs)
+fanX_min		Read/write the minimum speed of the fan.  Dropping
+			below this sets an alarm.
+
+(there are three PWMs, numbered pwm1 to pwm3):
+
+pwmX			Read/write the current duty cycle of the PWM.  Writes
+			only have effect when auto mode is turned off (see
+			below).  Range is 0 - 255.
+
+pwmX_enable		Fan speed control method:
+
+			0 - No control (fan at full speed)
+			1 - Manual fan speed control (using pwm[1-*])
+			2 - Automatic fan speed control
+
+pwmX_auto_channels_temp	Select which channels affect this PWM
+
+			1 - TEMP1 controls PWM
+			2 - TEMP2 controls PWM
+			4 - TEMP3 controls PWM
+			6 - TEMP2 and TEMP3 control PWM
+			7 - All three inputs control PWM
+
+pwmX_freq		Read/write the PWM frequency in Hz. The number
+			should be one of the following:
+
+			11 Hz
+			14 Hz
+			22 Hz
+			29 Hz
+			35 Hz
+			44 Hz
+			58 Hz
+			88 Hz
+
+pwmX_auto_point1_pwm	Read/write the minimum PWM duty cycle in automatic mode
+
+pwmX_auto_point2_pwm	Read/write the maximum PWM duty cycle in automatic mode
+
+(there are three temperature settings numbered temp1 to temp3):
+
+tempX_input		Read the current temperature.  The value is in milli
+			degrees of Celsius.
+
+tempX_max		Read/write the upper temperature limit - exceeding this
+			will cause an alarm.
+
+tempX_min		Read/write the lower temperature limit - exceeding this
+			will cause an alarm.
+
+tempX_offset		Read/write the temperature adjustment offset
+
+tempX_crit		Read/write the THERM limit for remote1.
+
+tempX_crit_hyst		Set the temperature value below crit where the
+			fans will stay on - this helps drive the temperature
+			low enough so it doesn't stay near the edge and
+			cause THERM to keep tripping.
+
+tempX_auto_point1_temp	Read/write the minimum temperature where the fans will
+			turn on in automatic mode.
+
+tempX_auto_point2_temp	Read/write the maximum temperature over which the fans
+			will run in automatic mode.  tempX_auto_point1_temp
+			and tempX_auto_point2_temp together define the
+			range of automatic control.
+
+tempX_alarm		Read a 1 if the max/min alarm is set
+tempX_fault		Read a 1 if either temp1 or temp3 diode has a fault
+
+(There are two voltage settings, in1 and in2):
+
+inX_input		Read the current voltage on VCC.  Value is in
+			millivolts.
+
+inX_min			read/write the minimum voltage limit.
+			Dropping below this causes an alarm.
+
+inX_max			read/write the maximum voltage limit.
+			Exceeding this causes an alarm.
+
+inX_alarm		Read a 1 if the max/min alarm is set.
diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig
index 4b33bc8..5c349a1 100644
--- a/drivers/hwmon/Kconfig
+++ b/drivers/hwmon/Kconfig
@@ -189,6 +189,16 @@ config SENSORS_ADT7473
 	  This driver can also be built as a module. If so, the module
 	  will be called adt7473.
 
+config SENSORS_ADT7475
+	tristate "Analog Devices ADT7475"
+	depends on I2C && EXPERIMENTAL
+	help
+	  If you say yes here you get support for the Analog Devices
+	  ADT7475 hardware monitoring chips.
+
+	  This driver can also be build as a module.  If so, the module
+	  will be called adt7475.
+
 config SENSORS_K8TEMP
 	tristate "AMD Athlon64/FX or Opteron temperature sensor"
 	depends on X86 && PCI && EXPERIMENTAL
diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile
index 19cb1ac..2e80f37 100644
--- a/drivers/hwmon/Makefile
+++ b/drivers/hwmon/Makefile
@@ -28,6 +28,8 @@ obj-$(CONFIG_SENSORS_ADS7828)	+= ads7828.o
 obj-$(CONFIG_SENSORS_ADT7462)	+= adt7462.o
 obj-$(CONFIG_SENSORS_ADT7470)	+= adt7470.o
 obj-$(CONFIG_SENSORS_ADT7473)	+= adt7473.o
+obj-$(CONFIG_SENSORS_ADT7475)	+= adt7475.o
+
 obj-$(CONFIG_SENSORS_APPLESMC)	+= applesmc.o
 obj-$(CONFIG_SENSORS_AMS)	+= ams/
 obj-$(CONFIG_SENSORS_ATXP1)	+= atxp1.o
diff --git a/drivers/hwmon/adt7475.c b/drivers/hwmon/adt7475.c
new file mode 100644
index 0000000..d39877a
--- /dev/null
+++ b/drivers/hwmon/adt7475.c
@@ -0,0 +1,1221 @@
+/*
+ * adt7475 - Thermal sensor driver for the ADT7475 chip and derivatives
+ * Copyright (C) 2007-2008, Advanced Micro Devices, Inc.
+ * Copyright (C) 2008 Jordan Crouse <jordan@cosmicpenguin.net>
+ * Copyright (C) 2008 Hans de Goede <hdegoede@redhat.com>
+
+ * Derived from the lm83 driver by Jean Delvare
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/slab.h>
+#include <linux/i2c.h>
+#include <linux/hwmon.h>
+#include <linux/hwmon-sysfs.h>
+#include <linux/err.h>
+
+/* Indexes for the sysfs hooks */
+
+#define INPUT		0
+#define MIN		1
+#define MAX		2
+#define CONTROL		3
+#define OFFSET		3
+#define AUTOMIN		4
+#define THERM		5
+#define HYSTERSIS	6
+
+/* These are unique identifiers for the sysfs functions - unlike the
+   numbers above, these are not also indexes into an array
+*/
+
+#define ALARM		9
+#define FAULT		10
+
+/* 7475 Common Registers */
+
+#define REG_VOLTAGE_BASE	0x21
+#define REG_TEMP_BASE		0x25
+#define REG_TACH_BASE		0x28
+#define REG_PWM_BASE		0x30
+#define REG_PWM_MAX_BASE	0x38
+
+#define REG_DEVID		0x3D
+#define REG_VENDID		0x3E
+
+#define REG_STATUS1		0x41
+#define REG_STATUS2		0x42
+
+#define REG_VOLTAGE_MIN_BASE	0x46
+#define REG_VOLTAGE_MAX_BASE	0x47
+
+#define REG_TEMP_MIN_BASE	0x4E
+#define REG_TEMP_MAX_BASE	0x4F
+
+#define REG_TACH_MIN_BASE	0x54
+
+#define REG_PWM_CONFIG_BASE	0x5C
+
+#define REG_TEMP_TRANGE_BASE	0x5F
+
+#define REG_PWM_MIN_BASE	0x64
+
+#define REG_TEMP_TMIN_BASE	0x67
+#define REG_TEMP_THERM_BASE	0x6A
+
+#define REG_REMOTE1_HYSTERSIS	0x6D
+#define REG_REMOTE2_HYSTERSIS	0x6E
+
+#define REG_TEMP_OFFSET_BASE	0x70
+
+#define REG_EXTEND1		0x76
+#define REG_EXTEND2		0x77
+#define REG_CONFIG5		0x7C
+
+#define CONFIG5_TWOSCOMP	0x01
+#define CONFIG5_TEMPOFFSET	0x02
+
+/* ADT7475 Settings */
+
+#define ADT7475_VOLTAGE_COUNT	2
+#define ADT7475_TEMP_COUNT	3
+#define ADT7475_TACH_COUNT	4
+#define ADT7475_PWM_COUNT	3
+
+/* Macro to read the registers */
+
+#define adt7475_read(reg) i2c_smbus_read_byte_data(client, (reg))
+
+/* Macros to easily index the registers */
+
+#define TACH_REG(idx) (REG_TACH_BASE + ((idx) * 2))
+#define TACH_MIN_REG(idx) (REG_TACH_MIN_BASE + ((idx) * 2))
+
+#define PWM_REG(idx) (REG_PWM_BASE + (idx))
+#define PWM_MAX_REG(idx) (REG_PWM_MAX_BASE + (idx))
+#define PWM_MIN_REG(idx) (REG_PWM_MIN_BASE + (idx))
+#define PWM_CONFIG_REG(idx) (REG_PWM_CONFIG_BASE + (idx))
+
+#define VOLTAGE_REG(idx) (REG_VOLTAGE_BASE + (idx))
+#define VOLTAGE_MIN_REG(idx) (REG_VOLTAGE_MIN_BASE + ((idx) * 2))
+#define VOLTAGE_MAX_REG(idx) (REG_VOLTAGE_MAX_BASE + ((idx) * 2))
+
+#define TEMP_REG(idx) (REG_TEMP_BASE + (idx))
+#define TEMP_MIN_REG(idx) (REG_TEMP_MIN_BASE + ((idx) * 2))
+#define TEMP_MAX_REG(idx) (REG_TEMP_MAX_BASE + ((idx) * 2))
+#define TEMP_TMIN_REG(idx) (REG_TEMP_TMIN_BASE + (idx))
+#define TEMP_THERM_REG(idx) (REG_TEMP_THERM_BASE + (idx))
+#define TEMP_OFFSET_REG(idx) (REG_TEMP_OFFSET_BASE + (idx))
+#define TEMP_TRANGE_REG(idx) (REG_TEMP_TRANGE_BASE + (idx))
+
+static unsigned short normal_i2c[] = { 0x2e, I2C_CLIENT_END };
+
+I2C_CLIENT_INSMOD_1(adt7475);
+
+static const struct i2c_device_id adt7475_id[] = {
+	{ "adt7475", adt7475 },
+	{ }
+};
+MODULE_DEVICE_TABLE(i2c, adt7475_id);
+
+struct adt7475_data {
+	struct device *hwmon_dev;
+	struct mutex lock;
+
+	unsigned long measure_updated;
+	unsigned long limits_updated;
+	char valid;
+
+	u8 config5;
+	u16 alarms;
+	u16 voltage[3][3];
+	u16 temp[7][3];
+	u16 tach[2][4];
+	u8 pwm[4][3];
+	u8 range[3];
+	u8 pwmctl[3];
+	u8 pwmchan[3];
+};
+
+static struct i2c_driver adt7475_driver;
+static struct adt7475_data *adt7475_update_device(struct device *dev);
+static void adt7475_read_hystersis(struct i2c_client *client);
+static void adt7475_read_pwm(struct i2c_client *client, int index);
+
+/* Given a temp value, convert it to register value */
+
+static inline u16 temp2reg(struct adt7475_data *data, long val)
+{
+	u16 ret;
+
+	if (!(data->config5 & CONFIG5_TWOSCOMP)) {
+		val = SENSORS_LIMIT(val, -64000, 191000);
+		ret = (val + 64500) / 1000;
+	} else {
+		val = SENSORS_LIMIT(val, -128000, 127000);
+		if (val < -500)
+			ret = (256500 + val) / 1000;
+		else
+			ret = (val + 500) / 1000;
+	}
+
+	return ret << 2;
+}
+
+/* Given a register value, convert it to a real temp value */
+
+static inline int reg2temp(struct adt7475_data *data, u16 reg)
+{
+	if (data->config5 & CONFIG5_TWOSCOMP) {
+		if (reg >= 512)
+			return (reg - 1024) * 250;
+		else
+			return reg * 250;
+	} else
+		return (reg - 256) * 250;
+}
+
+static inline int tach2rpm(u16 tach)
+{
+	if (tach == 0 || tach == 0xFFFF)
+		return 0;
+
+	return (90000 * 60) / tach;
+}
+
+static inline u16 rpm2tach(unsigned long rpm)
+{
+	if (rpm == 0)
+		return 0;
+
+	return SENSORS_LIMIT((90000 * 60) / rpm, 1, 0xFFFF);
+}
+
+static inline int reg2vcc(u16 reg)
+{
+	return (4296 * reg) / 1000;
+}
+
+static inline int reg2vccp(u16 reg)
+{
+	return (2929 * reg) / 1000;
+}
+
+static inline u16 vcc2reg(long vcc)
+{
+	vcc = SENSORS_LIMIT(vcc, 0, 4396);
+	return (vcc * 1000) / 4296;
+}
+
+static inline u16 vccp2reg(long vcc)
+{
+	vcc = SENSORS_LIMIT(vcc, 0, 2998);
+	return (vcc * 1000) / 2929;
+}
+
+static u16 adt7475_read_word(struct i2c_client *client, int reg)
+{
+	u16 val;
+
+	val = i2c_smbus_read_byte_data(client, reg);
+	val |= (i2c_smbus_read_byte_data(client, reg + 1) << 8);
+
+	return val;
+}
+
+static void adt7475_write_word(struct i2c_client *client, int reg, u16 val)
+{
+	i2c_smbus_write_byte_data(client, reg + 1, val >> 8);
+	i2c_smbus_write_byte_data(client, reg, val & 0xFF);
+}
+
+/* Find the nearest value in a table - used for pwm frequency and
+   auto temp range */
+static int find_nearest(long val, const int *array, int size)
+{
+	int i;
+
+	if (val < array[0])
+		return 0;
+
+	if (val > array[size - 1])
+		return size - 1;
+
+	for (i = 0; i < size - 1; i++) {
+		int a, b;
+
+		if (val > array[i + 1])
+			continue;
+
+		a = val - array[i];
+		b = array[i + 1] - val;
+
+		return (a <= b) ? i : i + 1;
+	}
+
+	return 0;
+}
+
+static ssize_t show_voltage(struct device *dev, struct device_attribute *attr,
+			    char *buf)
+{
+	struct adt7475_data *data = adt7475_update_device(dev);
+	struct sensor_device_attribute_2 *sattr = to_sensor_dev_attr_2(attr);
+	unsigned short val;
+
+	switch (sattr->nr) {
+	case ALARM:
+		return sprintf(buf, "%d\n",
+			       (data->alarms >> (sattr->index + 1)) & 1);
+	default:
+		val = data->voltage[sattr->nr][sattr->index];
+		return sprintf(buf, "%d\n",
+			       sattr->index ==
+			       0 ? reg2vccp(val) : reg2vcc(val));
+	}
+}
+
+static ssize_t set_voltage(struct device *dev, struct device_attribute *attr,
+			   const char *buf, size_t count)
+{
+
+	struct sensor_device_attribute_2 *sattr = to_sensor_dev_attr_2(attr);
+	struct i2c_client *client = to_i2c_client(dev);
+	struct adt7475_data *data = i2c_get_clientdata(client);
+	unsigned char reg;
+	long val;
+
+	if (strict_strtol(buf, 10, &val))
+		return -EINVAL;
+
+	mutex_lock(&data->lock);
+
+	data->voltage[sattr->nr][sattr->index] =
+		sattr->index ? vcc2reg(val) : vccp2reg(val);
+
+	if (sattr->nr == MIN)
+		reg = VOLTAGE_MIN_REG(sattr->index);
+	else
+		reg = VOLTAGE_MAX_REG(sattr->index);
+
+	i2c_smbus_write_byte_data(client, reg,
+				  data->voltage[sattr->nr][sattr->index] >> 2);
+	mutex_unlock(&data->lock);
+
+	return count;
+}
+
+static ssize_t show_temp(struct device *dev, struct device_attribute *attr,
+			 char *buf)
+{
+	struct adt7475_data *data = adt7475_update_device(dev);
+	struct sensor_device_attribute_2 *sattr = to_sensor_dev_attr_2(attr);
+	int out;
+
+	switch (sattr->nr) {
+	case HYSTERSIS:
+		mutex_lock(&data->lock);
+		out = data->temp[sattr->nr][sattr->index];
+		if (sattr->index != 1)
+			out = (out >> 4) & 0xF;
+		else
+			out = (out & 0xF);
+		/* Show the value as an absolute number tied to
+		 * THERM */
+		out = reg2temp(data, data->temp[THERM][sattr->index]) -
+			out * 1000;
+		mutex_unlock(&data->lock);
+		break;
+
+	case OFFSET:
+		/* Offset is always 2's complement, regardless of the
+		 * setting in CONFIG5 */
+		mutex_lock(&data->lock);
+		out = (s8)data->temp[sattr->nr][sattr->index];
+		if (data->config5 & CONFIG5_TEMPOFFSET)
+			out *= 1000;
+		else
+			out *= 500;
+		mutex_unlock(&data->lock);
+		break;
+
+	case ALARM:
+		out = (data->alarms >> (sattr->index + 4)) & 1;
+		break;
+
+	case FAULT:
+		/* Note - only for remote1 and remote2 */
+		out = data->alarms & (sattr->index ? 0x8000 : 0x4000);
+		out = out ? 0 : 1;
+		break;
+
+	default:
+		/* All other temp values are in the configured format */
+		out = reg2temp(data, data->temp[sattr->nr][sattr->index]);
+	}
+
+	return sprintf(buf, "%d\n", out);
+}
+
+static ssize_t set_temp(struct device *dev, struct device_attribute *attr,
+			const char *buf, size_t count)
+{
+	struct sensor_device_attribute_2 *sattr = to_sensor_dev_attr_2(attr);
+	struct i2c_client *client = to_i2c_client(dev);
+	struct adt7475_data *data = i2c_get_clientdata(client);
+	unsigned char reg = 0;
+	u8 out;
+	int temp;
+	long val;
+
+	if (strict_strtol(buf, 10, &val))
+		return -EINVAL;
+
+	mutex_lock(&data->lock);
+
+	/* We need the config register in all cases for temp <-> reg conv. */
+	data->config5 = adt7475_read(REG_CONFIG5);
+
+	switch (sattr->nr) {
+	case OFFSET:
+		if (data->config5 & CONFIG5_TEMPOFFSET) {
+			val = SENSORS_LIMIT(val, -63000, 127000);
+			out = data->temp[OFFSET][sattr->index] = val / 1000;
+		} else {
+			val = SENSORS_LIMIT(val, -63000, 64000);
+			out = data->temp[OFFSET][sattr->index] = val / 500;
+		}
+		break;
+
+	case HYSTERSIS:
+		/* The value will be given as an absolute value, turn it
+		   into an offset based on THERM */
+
+		/* Read fresh THERM and HYSTERSIS values from the chip */
+		data->temp[THERM][sattr->index] =
+			adt7475_read(TEMP_THERM_REG(sattr->index)) << 2;
+		adt7475_read_hystersis(client);
+
+		temp = reg2temp(data, data->temp[THERM][sattr->index]);
+		val = SENSORS_LIMIT(val, temp - 15000, temp);
+		val = (temp - val) / 1000;
+
+		if (sattr->index != 1) {
+			data->temp[HYSTERSIS][sattr->index] &= 0xF0;
+			data->temp[HYSTERSIS][sattr->index] |= (val & 0xF) << 4;
+		} else {
+			data->temp[HYSTERSIS][sattr->index] &= 0x0F;
+			data->temp[HYSTERSIS][sattr->index] |= (val & 0xF);
+		}
+
+		out = data->temp[HYSTERSIS][sattr->index];
+		break;
+
+	default:
+		data->temp[sattr->nr][sattr->index] = temp2reg(data, val);
+
+		/* We maintain an extra 2 digits of precision for simplicity
+		 * - shift those back off before writing the value */
+		out = (u8) (data->temp[sattr->nr][sattr->index] >> 2);
+	}
+
+	switch (sattr->nr) {
+	case MIN:
+		reg = TEMP_MIN_REG(sattr->index);
+		break;
+	case MAX:
+		reg = TEMP_MAX_REG(sattr->index);
+		break;
+	case OFFSET:
+		reg = TEMP_OFFSET_REG(sattr->index);
+		break;
+	case AUTOMIN:
+		reg = TEMP_TMIN_REG(sattr->index);
+		break;
+	case THERM:
+		reg = TEMP_THERM_REG(sattr->index);
+		break;
+	case HYSTERSIS:
+		if (sattr->index != 2)
+			reg = REG_REMOTE1_HYSTERSIS;
+		else
+			reg = REG_REMOTE2_HYSTERSIS;
+
+		break;
+	}
+
+	i2c_smbus_write_byte_data(client, reg, out);
+
+	mutex_unlock(&data->lock);
+	return count;
+}
+
+/* Table of autorange values - the user will write the value in millidegrees,
+   and we'll convert it */
+static const int autorange_table[] = {
+	2000, 2500, 3330, 4000, 5000, 6670, 8000,
+	10000, 13330, 16000, 20000, 26670, 32000, 40000,
+	53330, 80000
+};
+
+static ssize_t show_point2(struct device *dev, struct device_attribute *attr,
+			   char *buf)
+{
+	struct adt7475_data *data = adt7475_update_device(dev);
+	struct sensor_device_attribute_2 *sattr = to_sensor_dev_attr_2(attr);
+	int out, val;
+
+	mutex_lock(&data->lock);
+	out = (data->range[sattr->index] >> 4) & 0x0F;
+	val = reg2temp(data, data->temp[AUTOMIN][sattr->index]);
+	mutex_unlock(&data->lock);
+
+	return sprintf(buf, "%d\n", val + autorange_table[out]);
+}
+
+static ssize_t set_point2(struct device *dev, struct device_attribute *attr,
+			  const char *buf, size_t count)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct adt7475_data *data = i2c_get_clientdata(client);
+	struct sensor_device_attribute_2 *sattr = to_sensor_dev_attr_2(attr);
+	int temp;
+	long val;
+
+	if (strict_strtol(buf, 10, &val))
+		return -EINVAL;
+
+	mutex_lock(&data->lock);
+
+	/* Get a fresh copy of the needed registers */
+	data->config5 = adt7475_read(REG_CONFIG5);
+	data->temp[AUTOMIN][sattr->index] =
+		adt7475_read(TEMP_TMIN_REG(sattr->index)) << 2;
+	data->range[sattr->index] =
+		adt7475_read(TEMP_TRANGE_REG(sattr->index));
+
+	/* The user will write an absolute value, so subtract the start point
+	   to figure the range */
+	temp = reg2temp(data, data->temp[AUTOMIN][sattr->index]);
+	val = SENSORS_LIMIT(val, temp + autorange_table[0],
+		temp + autorange_table[ARRAY_SIZE(autorange_table) - 1]);
+	val -= temp;
+
+	/* Find the nearest table entry to what the user wrote */
+	val = find_nearest(val, autorange_table, ARRAY_SIZE(autorange_table));
+
+	data->range[sattr->index] &= ~0xF0;
+	data->range[sattr->index] |= val << 4;
+
+	i2c_smbus_write_byte_data(client, TEMP_TRANGE_REG(sattr->index),
+				  data->range[sattr->index]);
+
+	mutex_unlock(&data->lock);
+	return count;
+}
+
+static ssize_t show_tach(struct device *dev, struct device_attribute *attr,
+			 char *buf)
+{
+	struct adt7475_data *data = adt7475_update_device(dev);
+	struct sensor_device_attribute_2 *sattr = to_sensor_dev_attr_2(attr);
+	int out;
+
+	if (sattr->nr == ALARM)
+		out = (data->alarms >> (sattr->index + 10)) & 1;
+	else
+		out = tach2rpm(data->tach[sattr->nr][sattr->index]);
+
+	return sprintf(buf, "%d\n", out);
+}
+
+static ssize_t set_tach(struct device *dev, struct device_attribute *attr,
+			const char *buf, size_t count)
+{
+
+	struct sensor_device_attribute_2 *sattr = to_sensor_dev_attr_2(attr);
+	struct i2c_client *client = to_i2c_client(dev);
+	struct adt7475_data *data = i2c_get_clientdata(client);
+	unsigned long val;
+
+	if (strict_strtoul(buf, 10, &val))
+		return -EINVAL;
+
+	mutex_lock(&data->lock);
+
+	data->tach[MIN][sattr->index] = rpm2tach(val);
+
+	adt7475_write_word(client, TACH_MIN_REG(sattr->index),
+			   data->tach[MIN][sattr->index]);
+
+	mutex_unlock(&data->lock);
+	return count;
+}
+
+static ssize_t show_pwm(struct device *dev, struct device_attribute *attr,
+			char *buf)
+{
+	struct adt7475_data *data = adt7475_update_device(dev);
+	struct sensor_device_attribute_2 *sattr = to_sensor_dev_attr_2(attr);
+
+	return sprintf(buf, "%d\n", data->pwm[sattr->nr][sattr->index]);
+}
+
+static ssize_t show_pwmchan(struct device *dev, struct device_attribute *attr,
+			    char *buf)
+{
+	struct adt7475_data *data = adt7475_update_device(dev);
+	struct sensor_device_attribute_2 *sattr = to_sensor_dev_attr_2(attr);
+
+	return sprintf(buf, "%d\n", data->pwmchan[sattr->index]);
+}
+
+static ssize_t show_pwmctrl(struct device *dev, struct device_attribute *attr,
+			    char *buf)
+{
+	struct adt7475_data *data = adt7475_update_device(dev);
+	struct sensor_device_attribute_2 *sattr = to_sensor_dev_attr_2(attr);
+
+	return sprintf(buf, "%d\n", data->pwmctl[sattr->index]);
+}
+
+static ssize_t set_pwm(struct device *dev, struct device_attribute *attr,
+		       const char *buf, size_t count)
+{
+
+	struct sensor_device_attribute_2 *sattr = to_sensor_dev_attr_2(attr);
+	struct i2c_client *client = to_i2c_client(dev);
+	struct adt7475_data *data = i2c_get_clientdata(client);
+	unsigned char reg = 0;
+	long val;
+
+	if (strict_strtol(buf, 10, &val))
+		return -EINVAL;
+
+	mutex_lock(&data->lock);
+
+	switch (sattr->nr) {
+	case INPUT:
+		/* Get a fresh value for CONTROL */
+		data->pwm[CONTROL][sattr->index] =
+			adt7475_read(PWM_CONFIG_REG(sattr->index));
+
+		/* If we are not in manual mode, then we shouldn't allow
+		 * the user to set the pwm speed */
+		if (((data->pwm[CONTROL][sattr->index] >> 5) & 7) != 7) {
+			mutex_unlock(&data->lock);
+			return count;
+		}
+
+		reg = PWM_REG(sattr->index);
+		break;
+
+	case MIN:
+		reg = PWM_MIN_REG(sattr->index);
+		break;
+
+	case MAX:
+		reg = PWM_MAX_REG(sattr->index);
+		break;
+	}
+
+	data->pwm[sattr->nr][sattr->index] = SENSORS_LIMIT(val, 0, 0xFF);
+	i2c_smbus_write_byte_data(client, reg,
+				  data->pwm[sattr->nr][sattr->index]);
+
+	mutex_unlock(&data->lock);
+
+	return count;
+}
+
+/* Called by set_pwmctrl and set_pwmchan */
+
+static int hw_set_pwm(struct i2c_client *client, int index,
+		      unsigned int pwmctl, unsigned int pwmchan)
+{
+	struct adt7475_data *data = i2c_get_clientdata(client);
+	long val = 0;
+
+	switch (pwmctl) {
+	case 0:
+		val = 0x03;	/* Run at full speed */
+		break;
+	case 1:
+		val = 0x07;	/* Manual mode */
+		break;
+	case 2:
+		switch (pwmchan) {
+		case 1:
+			/* Remote1 controls PWM */
+			val = 0x00;
+			break;
+		case 2:
+			/* local controls PWM */
+			val = 0x01;
+			break;
+		case 4:
+			/* remote2 controls PWM */
+			val = 0x02;
+			break;
+		case 6:
+			/* local/remote2 control PWM */
+			val = 0x05;
+			break;
+		case 7:
+			/* All three control PWM */
+			val = 0x06;
+			break;
+		default:
+			return -EINVAL;
+		}
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	data->pwmctl[index] = pwmctl;
+	data->pwmchan[index] = pwmchan;
+
+	data->pwm[CONTROL][index] &= ~0xE0;
+	data->pwm[CONTROL][index] |= (val & 7) << 5;
+
+	i2c_smbus_write_byte_data(client, PWM_CONFIG_REG(index),
+				  data->pwm[CONTROL][index]);
+
+	return 0;
+}
+
+static ssize_t set_pwmchan(struct device *dev, struct device_attribute *attr,
+			   const char *buf, size_t count)
+{
+	struct sensor_device_attribute_2 *sattr = to_sensor_dev_attr_2(attr);
+	struct i2c_client *client = to_i2c_client(dev);
+	struct adt7475_data *data = i2c_get_clientdata(client);
+	int r;
+	long val;
+
+	if (strict_strtol(buf, 10, &val))
+		return -EINVAL;
+
+	mutex_lock(&data->lock);
+	/* Read Modify Write PWM values */
+	adt7475_read_pwm(client, sattr->index);
+	r = hw_set_pwm(client, sattr->index, data->pwmctl[sattr->index], val);
+	if (r)
+		count = r;
+	mutex_unlock(&data->lock);
+
+	return count;
+}
+
+static ssize_t set_pwmctrl(struct device *dev, struct device_attribute *attr,
+			   const char *buf, size_t count)
+{
+	struct sensor_device_attribute_2 *sattr = to_sensor_dev_attr_2(attr);
+	struct i2c_client *client = to_i2c_client(dev);
+	struct adt7475_data *data = i2c_get_clientdata(client);
+	int r;
+	long val;
+
+	if (strict_strtol(buf, 10, &val))
+		return -EINVAL;
+
+	mutex_lock(&data->lock);
+	/* Read Modify Write PWM values */
+	adt7475_read_pwm(client, sattr->index);
+	r = hw_set_pwm(client, sattr->index, val, data->pwmchan[sattr->index]);
+	if (r)
+		count = r;
+	mutex_unlock(&data->lock);
+
+	return count;
+}
+
+/* List of frequencies for the PWM */
+static const int pwmfreq_table[] = {
+	11, 14, 22, 29, 35, 44, 58, 88
+};
+
+static ssize_t show_pwmfreq(struct device *dev, struct device_attribute *attr,
+			    char *buf)
+{
+	struct adt7475_data *data = adt7475_update_device(dev);
+	struct sensor_device_attribute_2 *sattr = to_sensor_dev_attr_2(attr);
+
+	return sprintf(buf, "%d\n",
+		       pwmfreq_table[data->range[sattr->index] & 7]);
+}
+
+static ssize_t set_pwmfreq(struct device *dev, struct device_attribute *attr,
+			   const char *buf, size_t count)
+{
+	struct sensor_device_attribute_2 *sattr = to_sensor_dev_attr_2(attr);
+	struct i2c_client *client = to_i2c_client(dev);
+	struct adt7475_data *data = i2c_get_clientdata(client);
+	int out;
+	long val;
+
+	if (strict_strtol(buf, 10, &val))
+		return -EINVAL;
+
+	out = find_nearest(val, pwmfreq_table, ARRAY_SIZE(pwmfreq_table));
+
+	mutex_lock(&data->lock);
+
+	data->range[sattr->index] =
+		adt7475_read(TEMP_TRANGE_REG(sattr->index));
+	data->range[sattr->index] &= ~7;
+	data->range[sattr->index] |= out;
+
+	i2c_smbus_write_byte_data(client, TEMP_TRANGE_REG(sattr->index),
+				  data->range[sattr->index]);
+
+	mutex_unlock(&data->lock);
+	return count;
+}
+
+static SENSOR_DEVICE_ATTR_2(in1_input, S_IRUGO, show_voltage, NULL, INPUT, 0);
+static SENSOR_DEVICE_ATTR_2(in1_max, S_IRUGO | S_IWUSR, show_voltage,
+			    set_voltage, MAX, 0);
+static SENSOR_DEVICE_ATTR_2(in1_min, S_IRUGO | S_IWUSR, show_voltage,
+			    set_voltage, MIN, 0);
+static SENSOR_DEVICE_ATTR_2(in1_alarm, S_IRUGO, show_voltage, NULL, ALARM, 0);
+static SENSOR_DEVICE_ATTR_2(in2_input, S_IRUGO, show_voltage, NULL, INPUT, 1);
+static SENSOR_DEVICE_ATTR_2(in2_max, S_IRUGO | S_IWUSR, show_voltage,
+			    set_voltage, MAX, 1);
+static SENSOR_DEVICE_ATTR_2(in2_min, S_IRUGO | S_IWUSR, show_voltage,
+			    set_voltage, MIN, 1);
+static SENSOR_DEVICE_ATTR_2(in2_alarm, S_IRUGO, show_voltage, NULL, ALARM, 1);
+static SENSOR_DEVICE_ATTR_2(temp1_input, S_IRUGO, show_temp, NULL, INPUT, 0);
+static SENSOR_DEVICE_ATTR_2(temp1_alarm, S_IRUGO, show_temp, NULL, ALARM, 0);
+static SENSOR_DEVICE_ATTR_2(temp1_fault, S_IRUGO, show_temp, NULL, FAULT, 0);
+static SENSOR_DEVICE_ATTR_2(temp1_max, S_IRUGO | S_IWUSR, show_temp, set_temp,
+			    MAX, 0);
+static SENSOR_DEVICE_ATTR_2(temp1_min, S_IRUGO | S_IWUSR, show_temp, set_temp,
+			    MIN, 0);
+static SENSOR_DEVICE_ATTR_2(temp1_offset, S_IRUGO | S_IWUSR, show_temp,
+			    set_temp, OFFSET, 0);
+static SENSOR_DEVICE_ATTR_2(temp1_auto_point1_temp, S_IRUGO | S_IWUSR,
+			    show_temp, set_temp, AUTOMIN, 0);
+static SENSOR_DEVICE_ATTR_2(temp1_auto_point2_temp, S_IRUGO | S_IWUSR,
+			    show_point2, set_point2, 0, 0);
+static SENSOR_DEVICE_ATTR_2(temp1_crit, S_IRUGO | S_IWUSR, show_temp, set_temp,
+			    THERM, 0);
+static SENSOR_DEVICE_ATTR_2(temp1_crit_hyst, S_IRUGO | S_IWUSR, show_temp,
+			    set_temp, HYSTERSIS, 0);
+static SENSOR_DEVICE_ATTR_2(temp2_input, S_IRUGO, show_temp, NULL, INPUT, 1);
+static SENSOR_DEVICE_ATTR_2(temp2_alarm, S_IRUGO, show_temp, NULL, ALARM, 1);
+static SENSOR_DEVICE_ATTR_2(temp2_max, S_IRUGO | S_IWUSR, show_temp, set_temp,
+			    MAX, 1);
+static SENSOR_DEVICE_ATTR_2(temp2_min, S_IRUGO | S_IWUSR, show_temp, set_temp,
+			    MIN, 1);
+static SENSOR_DEVICE_ATTR_2(temp2_offset, S_IRUGO | S_IWUSR, show_temp,
+			    set_temp, OFFSET, 1);
+static SENSOR_DEVICE_ATTR_2(temp2_auto_point1_temp, S_IRUGO | S_IWUSR,
+			    show_temp, set_temp, AUTOMIN, 1);
+static SENSOR_DEVICE_ATTR_2(temp2_auto_point2_temp, S_IRUGO | S_IWUSR,
+			    show_point2, set_point2, 0, 1);
+static SENSOR_DEVICE_ATTR_2(temp2_crit, S_IRUGO | S_IWUSR, show_temp, set_temp,
+			    THERM, 1);
+static SENSOR_DEVICE_ATTR_2(temp2_crit_hyst, S_IRUGO | S_IWUSR, show_temp,
+			    set_temp, HYSTERSIS, 1);
+static SENSOR_DEVICE_ATTR_2(temp3_input, S_IRUGO, show_temp, NULL, INPUT, 2);
+static SENSOR_DEVICE_ATTR_2(temp3_alarm, S_IRUGO, show_temp, NULL, ALARM, 2);
+static SENSOR_DEVICE_ATTR_2(temp3_fault, S_IRUGO, show_temp, NULL, FAULT, 2);
+static SENSOR_DEVICE_ATTR_2(temp3_max, S_IRUGO | S_IWUSR, show_temp, set_temp,
+			    MAX, 2);
+static SENSOR_DEVICE_ATTR_2(temp3_min, S_IRUGO | S_IWUSR, show_temp, set_temp,
+			    MIN, 2);
+static SENSOR_DEVICE_ATTR_2(temp3_offset, S_IRUGO | S_IWUSR, show_temp,
+			    set_temp, OFFSET, 2);
+static SENSOR_DEVICE_ATTR_2(temp3_auto_point1_temp, S_IRUGO | S_IWUSR,
+			    show_temp, set_temp, AUTOMIN, 2);
+static SENSOR_DEVICE_ATTR_2(temp3_auto_point2_temp, S_IRUGO | S_IWUSR,
+			    show_point2, set_point2, 0, 2);
+static SENSOR_DEVICE_ATTR_2(temp3_crit, S_IRUGO | S_IWUSR, show_temp, set_temp,
+			    THERM, 2);
+static SENSOR_DEVICE_ATTR_2(temp3_crit_hyst, S_IRUGO | S_IWUSR, show_temp,
+			    set_temp, HYSTERSIS, 2);
+static SENSOR_DEVICE_ATTR_2(fan1_input, S_IRUGO, show_tach, NULL, INPUT, 0);
+static SENSOR_DEVICE_ATTR_2(fan1_min, S_IRUGO | S_IWUSR, show_tach, set_tach,
+			    MIN, 0);
+static SENSOR_DEVICE_ATTR_2(fan1_alarm, S_IRUGO, show_tach, NULL, ALARM, 0);
+static SENSOR_DEVICE_ATTR_2(fan2_input, S_IRUGO, show_tach, NULL, INPUT, 1);
+static SENSOR_DEVICE_ATTR_2(fan2_min, S_IRUGO | S_IWUSR, show_tach, set_tach,
+			    MIN, 1);
+static SENSOR_DEVICE_ATTR_2(fan2_alarm, S_IRUGO, show_tach, NULL, ALARM, 1);
+static SENSOR_DEVICE_ATTR_2(fan3_input, S_IRUGO, show_tach, NULL, INPUT, 2);
+static SENSOR_DEVICE_ATTR_2(fan3_min, S_IRUGO | S_IWUSR, show_tach, set_tach,
+			    MIN, 2);
+static SENSOR_DEVICE_ATTR_2(fan3_alarm, S_IRUGO, show_tach, NULL, ALARM, 2);
+static SENSOR_DEVICE_ATTR_2(fan4_input, S_IRUGO, show_tach, NULL, INPUT, 3);
+static SENSOR_DEVICE_ATTR_2(fan4_min, S_IRUGO | S_IWUSR, show_tach, set_tach,
+			    MIN, 3);
+static SENSOR_DEVICE_ATTR_2(fan4_alarm, S_IRUGO, show_tach, NULL, ALARM, 3);
+static SENSOR_DEVICE_ATTR_2(pwm1, S_IRUGO | S_IWUSR, show_pwm, set_pwm, INPUT,
+			    0);
+static SENSOR_DEVICE_ATTR_2(pwm1_freq, S_IRUGO | S_IWUSR, show_pwmfreq,
+			    set_pwmfreq, INPUT, 0);
+static SENSOR_DEVICE_ATTR_2(pwm1_enable, S_IRUGO | S_IWUSR, show_pwmctrl,
+			    set_pwmctrl, INPUT, 0);
+static SENSOR_DEVICE_ATTR_2(pwm1_auto_channel_temp, S_IRUGO | S_IWUSR,
+			    show_pwmchan, set_pwmchan, INPUT, 0);
+static SENSOR_DEVICE_ATTR_2(pwm1_auto_point1_pwm, S_IRUGO | S_IWUSR, show_pwm,
+			    set_pwm, MIN, 0);
+static SENSOR_DEVICE_ATTR_2(pwm1_auto_point2_pwm, S_IRUGO | S_IWUSR, show_pwm,
+			    set_pwm, MAX, 0);
+static SENSOR_DEVICE_ATTR_2(pwm2, S_IRUGO | S_IWUSR, show_pwm, set_pwm, INPUT,
+			    1);
+static SENSOR_DEVICE_ATTR_2(pwm2_freq, S_IRUGO | S_IWUSR, show_pwmfreq,
+			    set_pwmfreq, INPUT, 1);
+static SENSOR_DEVICE_ATTR_2(pwm2_enable, S_IRUGO | S_IWUSR, show_pwmctrl,
+			    set_pwmctrl, INPUT, 1);
+static SENSOR_DEVICE_ATTR_2(pwm2_auto_channel_temp, S_IRUGO | S_IWUSR,
+			    show_pwmchan, set_pwmchan, INPUT, 1);
+static SENSOR_DEVICE_ATTR_2(pwm2_auto_point1_pwm, S_IRUGO | S_IWUSR, show_pwm,
+			    set_pwm, MIN, 1);
+static SENSOR_DEVICE_ATTR_2(pwm2_auto_point2_pwm, S_IRUGO | S_IWUSR, show_pwm,
+			    set_pwm, MAX, 1);
+static SENSOR_DEVICE_ATTR_2(pwm3, S_IRUGO | S_IWUSR, show_pwm, set_pwm, INPUT,
+			    2);
+static SENSOR_DEVICE_ATTR_2(pwm3_freq, S_IRUGO | S_IWUSR, show_pwmfreq,
+			    set_pwmfreq, INPUT, 2);
+static SENSOR_DEVICE_ATTR_2(pwm3_enable, S_IRUGO | S_IWUSR, show_pwmctrl,
+			    set_pwmctrl, INPUT, 2);
+static SENSOR_DEVICE_ATTR_2(pwm3_auto_channel_temp, S_IRUGO | S_IWUSR,
+			    show_pwmchan, set_pwmchan, INPUT, 2);
+static SENSOR_DEVICE_ATTR_2(pwm3_auto_point1_pwm, S_IRUGO | S_IWUSR, show_pwm,
+			    set_pwm, MIN, 2);
+static SENSOR_DEVICE_ATTR_2(pwm3_auto_point2_pwm, S_IRUGO | S_IWUSR, show_pwm,
+			    set_pwm, MAX, 2);
+
+static struct attribute *adt7475_attrs[] = {
+	&sensor_dev_attr_in1_input.dev_attr.attr,
+	&sensor_dev_attr_in1_max.dev_attr.attr,
+	&sensor_dev_attr_in1_min.dev_attr.attr,
+	&sensor_dev_attr_in1_alarm.dev_attr.attr,
+	&sensor_dev_attr_in2_input.dev_attr.attr,
+	&sensor_dev_attr_in2_max.dev_attr.attr,
+	&sensor_dev_attr_in2_min.dev_attr.attr,
+	&sensor_dev_attr_in2_alarm.dev_attr.attr,
+	&sensor_dev_attr_temp1_input.dev_attr.attr,
+	&sensor_dev_attr_temp1_alarm.dev_attr.attr,
+	&sensor_dev_attr_temp1_fault.dev_attr.attr,
+	&sensor_dev_attr_temp1_max.dev_attr.attr,
+	&sensor_dev_attr_temp1_min.dev_attr.attr,
+	&sensor_dev_attr_temp1_offset.dev_attr.attr,
+	&sensor_dev_attr_temp1_auto_point1_temp.dev_attr.attr,
+	&sensor_dev_attr_temp1_auto_point2_temp.dev_attr.attr,
+	&sensor_dev_attr_temp1_crit.dev_attr.attr,
+	&sensor_dev_attr_temp1_crit_hyst.dev_attr.attr,
+	&sensor_dev_attr_temp2_input.dev_attr.attr,
+	&sensor_dev_attr_temp2_alarm.dev_attr.attr,
+	&sensor_dev_attr_temp2_max.dev_attr.attr,
+	&sensor_dev_attr_temp2_min.dev_attr.attr,
+	&sensor_dev_attr_temp2_offset.dev_attr.attr,
+	&sensor_dev_attr_temp2_auto_point1_temp.dev_attr.attr,
+	&sensor_dev_attr_temp2_auto_point2_temp.dev_attr.attr,
+	&sensor_dev_attr_temp2_crit.dev_attr.attr,
+	&sensor_dev_attr_temp2_crit_hyst.dev_attr.attr,
+	&sensor_dev_attr_temp3_input.dev_attr.attr,
+	&sensor_dev_attr_temp3_fault.dev_attr.attr,
+	&sensor_dev_attr_temp3_alarm.dev_attr.attr,
+	&sensor_dev_attr_temp3_max.dev_attr.attr,
+	&sensor_dev_attr_temp3_min.dev_attr.attr,
+	&sensor_dev_attr_temp3_offset.dev_attr.attr,
+	&sensor_dev_attr_temp3_auto_point1_temp.dev_attr.attr,
+	&sensor_dev_attr_temp3_auto_point2_temp.dev_attr.attr,
+	&sensor_dev_attr_temp3_crit.dev_attr.attr,
+	&sensor_dev_attr_temp3_crit_hyst.dev_attr.attr,
+	&sensor_dev_attr_fan1_input.dev_attr.attr,
+	&sensor_dev_attr_fan1_min.dev_attr.attr,
+	&sensor_dev_attr_fan1_alarm.dev_attr.attr,
+	&sensor_dev_attr_fan2_input.dev_attr.attr,
+	&sensor_dev_attr_fan2_min.dev_attr.attr,
+	&sensor_dev_attr_fan2_alarm.dev_attr.attr,
+	&sensor_dev_attr_fan3_input.dev_attr.attr,
+	&sensor_dev_attr_fan3_min.dev_attr.attr,
+	&sensor_dev_attr_fan3_alarm.dev_attr.attr,
+	&sensor_dev_attr_fan4_input.dev_attr.attr,
+	&sensor_dev_attr_fan4_min.dev_attr.attr,
+	&sensor_dev_attr_fan4_alarm.dev_attr.attr,
+	&sensor_dev_attr_pwm1.dev_attr.attr,
+	&sensor_dev_attr_pwm1_freq.dev_attr.attr,
+	&sensor_dev_attr_pwm1_enable.dev_attr.attr,
+	&sensor_dev_attr_pwm1_auto_channel_temp.dev_attr.attr,
+	&sensor_dev_attr_pwm1_auto_point1_pwm.dev_attr.attr,
+	&sensor_dev_attr_pwm1_auto_point2_pwm.dev_attr.attr,
+	&sensor_dev_attr_pwm2.dev_attr.attr,
+	&sensor_dev_attr_pwm2_freq.dev_attr.attr,
+	&sensor_dev_attr_pwm2_enable.dev_attr.attr,
+	&sensor_dev_attr_pwm2_auto_channel_temp.dev_attr.attr,
+	&sensor_dev_attr_pwm2_auto_point1_pwm.dev_attr.attr,
+	&sensor_dev_attr_pwm2_auto_point2_pwm.dev_attr.attr,
+	&sensor_dev_attr_pwm3.dev_attr.attr,
+	&sensor_dev_attr_pwm3_freq.dev_attr.attr,
+	&sensor_dev_attr_pwm3_enable.dev_attr.attr,
+	&sensor_dev_attr_pwm3_auto_channel_temp.dev_attr.attr,
+	&sensor_dev_attr_pwm3_auto_point1_pwm.dev_attr.attr,
+	&sensor_dev_attr_pwm3_auto_point2_pwm.dev_attr.attr,
+	NULL,
+};
+
+struct attribute_group adt7475_attr_group = { .attrs = adt7475_attrs };
+
+static int adt7475_detect(struct i2c_client *client, int kind,
+			  struct i2c_board_info *info)
+{
+	struct i2c_adapter *adapter = client->adapter;
+
+	if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA))
+		return -ENODEV;
+
+	if (kind <= 0) {
+		if (adt7475_read(REG_VENDID) != 0x41 ||
+		    adt7475_read(REG_DEVID) != 0x75) {
+			dev_err(&adapter->dev,
+				"Couldn't detect a adt7475 part at 0x%02x\n",
+				(unsigned int)client->addr);
+			return -ENODEV;
+		}
+	}
+
+	strlcpy(info->type, adt7475_id[0].name, I2C_NAME_SIZE);
+
+	return 0;
+}
+
+static int adt7475_probe(struct i2c_client *client,
+			 const struct i2c_device_id *id)
+{
+	struct adt7475_data *data;
+	int i, ret = 0;
+
+	data = kzalloc(sizeof(*data), GFP_KERNEL);
+	if (data == NULL)
+		return -ENOMEM;
+
+	mutex_init(&data->lock);
+	i2c_set_clientdata(client, data);
+
+	/* Call adt7475_read_pwm for all pwm's as this will reprogram any
+	   pwm's which are disabled to manual mode with 0% duty cycle */
+	for (i = 0; i < ADT7475_PWM_COUNT; i++)
+		adt7475_read_pwm(client, i);
+
+	ret = sysfs_create_group(&client->dev.kobj, &adt7475_attr_group);
+	if (ret)
+		goto efree;
+
+	data->hwmon_dev = hwmon_device_register(&client->dev);
+	if (IS_ERR(data->hwmon_dev)) {
+		ret = PTR_ERR(data->hwmon_dev);
+		goto eremove;
+	}
+
+	return 0;
+
+eremove:
+	sysfs_remove_group(&client->dev.kobj, &adt7475_attr_group);
+efree:
+	kfree(data);
+	return ret;
+}
+
+static int adt7475_remove(struct i2c_client *client)
+{
+	struct adt7475_data *data = i2c_get_clientdata(client);
+
+	hwmon_device_unregister(data->hwmon_dev);
+	sysfs_remove_group(&client->dev.kobj, &adt7475_attr_group);
+	kfree(data);
+
+	return 0;
+}
+
+static struct i2c_driver adt7475_driver = {
+	.class		= I2C_CLASS_HWMON,
+	.driver = {
+		.name	= "adt7475",
+	},
+	.probe		= adt7475_probe,
+	.remove		= adt7475_remove,
+	.id_table	= adt7475_id,
+	.detect		= adt7475_detect,
+	.address_data	= &addr_data,
+};
+
+static void adt7475_read_hystersis(struct i2c_client *client)
+{
+	struct adt7475_data *data = i2c_get_clientdata(client);
+
+	data->temp[HYSTERSIS][0] = (u16) adt7475_read(REG_REMOTE1_HYSTERSIS);
+	data->temp[HYSTERSIS][1] = data->temp[HYSTERSIS][0];
+	data->temp[HYSTERSIS][2] = (u16) adt7475_read(REG_REMOTE2_HYSTERSIS);
+}
+
+static void adt7475_read_pwm(struct i2c_client *client, int index)
+{
+	struct adt7475_data *data = i2c_get_clientdata(client);
+	unsigned int v;
+
+	data->pwm[CONTROL][index] = adt7475_read(PWM_CONFIG_REG(index));
+
+	/* Figure out the internal value for pwmctrl and pwmchan
+	   based on the current settings */
+	v = (data->pwm[CONTROL][index] >> 5) & 7;
+
+	if (v == 3)
+		data->pwmctl[index] = 0;
+	else if (v == 7)
+		data->pwmctl[index] = 1;
+	else if (v == 4) {
+		/* The fan is disabled - we don't want to
+		   support that, so change to manual mode and
+		   set the duty cycle to 0 instead
+		*/
+		data->pwm[INPUT][index] = 0;
+		data->pwm[CONTROL][index] &= ~0xE0;
+		data->pwm[CONTROL][index] |= (7 << 5);
+
+		i2c_smbus_write_byte_data(client, PWM_CONFIG_REG(index),
+					  data->pwm[INPUT][index]);
+
+		i2c_smbus_write_byte_data(client, PWM_CONFIG_REG(index),
+					  data->pwm[CONTROL][index]);
+
+		data->pwmctl[index] = 1;
+	} else {
+		data->pwmctl[index] = 2;
+
+		switch (v) {
+		case 0:
+			data->pwmchan[index] = 1;
+			break;
+		case 1:
+			data->pwmchan[index] = 2;
+			break;
+		case 2:
+			data->pwmchan[index] = 4;
+			break;
+		case 5:
+			data->pwmchan[index] = 6;
+			break;
+		case 6:
+			data->pwmchan[index] = 7;
+			break;
+		}
+	}
+}
+
+static struct adt7475_data *adt7475_update_device(struct device *dev)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct adt7475_data *data = i2c_get_clientdata(client);
+	u8 ext;
+	int i;
+
+	mutex_lock(&data->lock);
+
+	/* Measurement values update every 2 seconds */
+	if (time_after(jiffies, data->measure_updated + HZ * 2) ||
+	    !data->valid) {
+		data->alarms = adt7475_read(REG_STATUS2) << 8;
+		data->alarms |= adt7475_read(REG_STATUS1);
+
+		ext = adt7475_read(REG_EXTEND1);
+		for (i = 0; i < ADT7475_VOLTAGE_COUNT; i++)
+			data->voltage[INPUT][i] =
+				(adt7475_read(VOLTAGE_REG(i)) << 2) |
+				((ext >> ((i + 1) * 2)) & 3);
+
+		ext = adt7475_read(REG_EXTEND2);
+		for (i = 0; i < ADT7475_TEMP_COUNT; i++)
+			data->temp[INPUT][i] =
+				(adt7475_read(TEMP_REG(i)) << 2) |
+				((ext >> ((i + 1) * 2)) & 3);
+
+		for (i = 0; i < ADT7475_TACH_COUNT; i++)
+			data->tach[INPUT][i] =
+				adt7475_read_word(client, TACH_REG(i));
+
+		/* Updated by hw when in auto mode */
+		for (i = 0; i < ADT7475_PWM_COUNT; i++)
+			data->pwm[INPUT][i] = adt7475_read(PWM_REG(i));
+
+		data->measure_updated = jiffies;
+	}
+
+	/* Limits and settings, should never change update every 60 seconds */
+	if (time_after(jiffies, data->limits_updated + HZ * 2) ||
+	    !data->valid) {
+		data->config5 = adt7475_read(REG_CONFIG5);
+
+		for (i = 0; i < ADT7475_VOLTAGE_COUNT; i++) {
+			/* Adjust values so they match the input precision */
+			data->voltage[MIN][i] =
+				adt7475_read(VOLTAGE_MIN_REG(i)) << 2;
+			data->voltage[MAX][i] =
+				adt7475_read(VOLTAGE_MAX_REG(i)) << 2;
+		}
+
+		for (i = 0; i < ADT7475_TEMP_COUNT; i++) {
+			/* Adjust values so they match the input precision */
+			data->temp[MIN][i] =
+				adt7475_read(TEMP_MIN_REG(i)) << 2;
+			data->temp[MAX][i] =
+				adt7475_read(TEMP_MAX_REG(i)) << 2;
+			data->temp[AUTOMIN][i] =
+				adt7475_read(TEMP_TMIN_REG(i)) << 2;
+			data->temp[THERM][i] =
+				adt7475_read(TEMP_THERM_REG(i)) << 2;
+			data->temp[OFFSET][i] =
+				adt7475_read(TEMP_OFFSET_REG(i));
+		}
+		adt7475_read_hystersis(client);
+
+		for (i = 0; i < ADT7475_TACH_COUNT; i++)
+			data->tach[MIN][i] =
+				adt7475_read_word(client, TACH_MIN_REG(i));
+
+		for (i = 0; i < ADT7475_PWM_COUNT; i++) {
+			data->pwm[MAX][i] = adt7475_read(PWM_MAX_REG(i));
+			data->pwm[MIN][i] = adt7475_read(PWM_MIN_REG(i));
+			/* Set the channel and control information */
+			adt7475_read_pwm(client, i);
+		}
+
+		data->range[0] = adt7475_read(TEMP_TRANGE_REG(0));
+		data->range[1] = adt7475_read(TEMP_TRANGE_REG(1));
+		data->range[2] = adt7475_read(TEMP_TRANGE_REG(2));
+
+		data->limits_updated = jiffies;
+		data->valid = 1;
+	}
+
+	mutex_unlock(&data->lock);
+
+	return data;
+}
+
+static int __init sensors_adt7475_init(void)
+{
+	return i2c_add_driver(&adt7475_driver);
+}
+
+static void __exit sensors_adt7475_exit(void)
+{
+	i2c_del_driver(&adt7475_driver);
+}
+
+MODULE_AUTHOR("Advanced Micro Devices, Inc");
+MODULE_DESCRIPTION("adt7475 driver");
+MODULE_LICENSE("GPL");
+
+module_init(sensors_adt7475_init);
+module_exit(sensors_adt7475_exit);