Linux-2.6.12-rc2

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!

1 files changed, 91 insertions, 0 deletions

diff --git a/Documentation/aoe/aoe.txt b/Documentation/aoe/aoe.txt
new file mode 100644
index 0000000..43e5010
--- /dev/null
+++ b/Documentation/aoe/aoe.txt
@@ -0,0 +1,91 @@
+The EtherDrive (R) HOWTO for users of 2.6 kernels is found at ...
+
+  http://www.coraid.com/support/linux/EtherDrive-2.6-HOWTO.html
+
+  It has many tips and hints!
+
+CREATING DEVICE NODES
+
+  Users of udev should find the block device nodes created
+  automatically, but to create all the necessary device nodes, use the
+  udev configuration rules provided in udev.txt (in this directory).
+
+  There is a udev-install.sh script that shows how to install these
+  rules on your system.
+
+  If you are not using udev, two scripts are provided in
+  Documentation/aoe as examples of static device node creation for
+  using the aoe driver.
+
+    rm -rf /dev/etherd
+    sh Documentation/aoe/mkdevs.sh /dev/etherd
+
+  ... or to make just one shelf's worth of block device nodes ...
+
+    sh Documentation/aoe/mkshelf.sh /dev/etherd 0
+
+  There is also an autoload script that shows how to edit
+  /etc/modprobe.conf to ensure that the aoe module is loaded when
+  necessary.
+
+USING DEVICE NODES
+
+  "cat /dev/etherd/err" blocks, waiting for error diagnostic output,
+  like any retransmitted packets.
+
+  "echo eth2 eth4 > /dev/etherd/interfaces" tells the aoe driver to
+  limit ATA over Ethernet traffic to eth2 and eth4.  AoE traffic from
+  untrusted networks should be ignored as a matter of security.
+
+  "echo > /dev/etherd/discover" tells the driver to find out what AoE
+  devices are available.
+
+  These character devices may disappear and be replaced by sysfs
+  counterparts, so distribution maintainers are encouraged to create
+  scripts that use these devices.
+
+  The block devices are named like this:
+
+	e{shelf}.{slot}
+	e{shelf}.{slot}p{part}
+
+  ... so that "e0.2" is the third blade from the left (slot 2) in the
+  first shelf (shelf address zero).  That's the whole disk.  The first
+  partition on that disk would be "e0.2p1".
+
+USING SYSFS
+
+  Each aoe block device in /sys/block has the extra attributes of
+  state, mac, and netif.  The state attribute is "up" when the device
+  is ready for I/O and "down" if detected but unusable.  The
+  "down,closewait" state shows that the device is still open and
+  cannot come up again until it has been closed.
+
+  The mac attribute is the ethernet address of the remote AoE device.
+  The netif attribute is the network interface on the localhost
+  through which we are communicating with the remote AoE device.
+
+  There is a script in this directory that formats this information
+  in a convenient way.
+
+  root@makki root# sh Documentation/aoe/status.sh 
+     e10.0            eth3              up
+     e10.1            eth3              up
+     e10.2            eth3              up
+     e10.3            eth3              up
+     e10.4            eth3              up
+     e10.5            eth3              up
+     e10.6            eth3              up
+     e10.7            eth3              up
+     e10.8            eth3              up
+     e10.9            eth3              up
+      e4.0            eth1              up
+      e4.1            eth1              up
+      e4.2            eth1              up
+      e4.3            eth1              up
+      e4.4            eth1              up
+      e4.5            eth1              up
+      e4.6            eth1              up
+      e4.7            eth1              up
+      e4.8            eth1              up
+      e4.9            eth1              up