sh: Mass ctrl_in/outX to __raw_read/writeX conversion.

The old ctrl in/out routines are non-portable and unsuitable for
cross-platform use. While drivers/sh has already been sanitized, there
is still quite a lot of code that is not. This converts the arch/sh/ bits
over, which permits us to flag the routines as deprecated whilst still
building with -Werror for the architecture code, and to ensure that
future users are not added.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>

49 files changed, 359 insertions, 359 deletions

diff --git a/arch/sh/boards/board-magicpanelr2.c b/arch/sh/boards/board-magicpanelr2.c
index 99ffc5f..efba450 100644
--- a/arch/sh/boards/board-magicpanelr2.c
+++ b/arch/sh/boards/board-magicpanelr2.c
@@ -23,7 +23,7 @@
 #include <asm/heartbeat.h>
 #include <cpu/sh7720.h>
 
-#define LAN9115_READY	(ctrl_inl(0xA8000084UL) & 0x00000001UL)
+#define LAN9115_READY	(__raw_readl(0xA8000084UL) & 0x00000001UL)
 
 /* Prefer cmdline over RedBoot */
 static const char *probes[] = { "cmdlinepart", "RedBoot", NULL };
@@ -60,33 +60,33 @@ static void __init setup_chip_select(void)
 {
 	/* CS2: LAN (0x08000000 - 0x0bffffff) */
 	/* no idle cycles, normal space, 8 bit data bus */
-	ctrl_outl(0x36db0400, CS2BCR);
+	__raw_writel(0x36db0400, CS2BCR);
 	/* (SW:1.5 WR:3 HW:1.5), ext. wait */
-	ctrl_outl(0x000003c0, CS2WCR);
+	__raw_writel(0x000003c0, CS2WCR);
 
 	/* CS4: CAN1 (0xb0000000 - 0xb3ffffff) */
 	/* no idle cycles, normal space, 8 bit data bus */
-	ctrl_outl(0x00000200, CS4BCR);
+	__raw_writel(0x00000200, CS4BCR);
 	/* (SW:1.5 WR:3 HW:1.5), ext. wait */
-	ctrl_outl(0x00100981, CS4WCR);
+	__raw_writel(0x00100981, CS4WCR);
 
 	/* CS5a: CAN2 (0xb4000000 - 0xb5ffffff) */
 	/* no idle cycles, normal space, 8 bit data bus */
-	ctrl_outl(0x00000200, CS5ABCR);
+	__raw_writel(0x00000200, CS5ABCR);
 	/* (SW:1.5 WR:3 HW:1.5), ext. wait */
-	ctrl_outl(0x00100981, CS5AWCR);
+	__raw_writel(0x00100981, CS5AWCR);
 
 	/* CS5b: CAN3 (0xb6000000 - 0xb7ffffff) */
 	/* no idle cycles, normal space, 8 bit data bus */
-	ctrl_outl(0x00000200, CS5BBCR);
+	__raw_writel(0x00000200, CS5BBCR);
 	/* (SW:1.5 WR:3 HW:1.5), ext. wait */
-	ctrl_outl(0x00100981, CS5BWCR);
+	__raw_writel(0x00100981, CS5BWCR);
 
 	/* CS6a: Rotary (0xb8000000 - 0xb9ffffff) */
 	/* no idle cycles, normal space, 8 bit data bus */
-	ctrl_outl(0x00000200, CS6ABCR);
+	__raw_writel(0x00000200, CS6ABCR);
 	/* (SW:1.5 WR:3 HW:1.5), no ext. wait */
-	ctrl_outl(0x001009C1, CS6AWCR);
+	__raw_writel(0x001009C1, CS6AWCR);
 }
 
 static void __init setup_port_multiplexing(void)
@@ -94,71 +94,71 @@ static void __init setup_port_multiplexing(void)
 	/* A7 GPO(LED8);     A6 GPO(LED7);     A5 GPO(LED6);	  A4 GPO(LED5);
 	 * A3 GPO(LED4);     A2 GPO(LED3);     A1 GPO(LED2);	  A0 GPO(LED1);
 	 */
-	ctrl_outw(0x5555, PORT_PACR);	/* 01 01 01 01 01 01 01 01 */
+	__raw_writew(0x5555, PORT_PACR);	/* 01 01 01 01 01 01 01 01 */
 
 	/* B7 GPO(RST4);   B6 GPO(RST3);  B5 GPO(RST2);    B4 GPO(RST1);
 	 * B3 GPO(PB3);	   B2 GPO(PB2);	  B1 GPO(PB1);	   B0 GPO(PB0);
 	 */
-	ctrl_outw(0x5555, PORT_PBCR);	/* 01 01 01 01 01 01 01 01 */
+	__raw_writew(0x5555, PORT_PBCR);	/* 01 01 01 01 01 01 01 01 */
 
 	/* C7 GPO(PC7);	  C6 GPO(PC6);	  C5 GPO(PC5);	   C4 GPO(PC4);
 	 * C3 LCD_DATA3;  C2 LCD_DATA2;   C1 LCD_DATA1;	   C0 LCD_DATA0;
 	 */
-	ctrl_outw(0x5500, PORT_PCCR);	/* 01 01 01 01 00 00 00 00 */
+	__raw_writew(0x5500, PORT_PCCR);	/* 01 01 01 01 00 00 00 00 */
 
 	/* D7 GPO(PD7);	D6 GPO(PD6);	D5 GPO(PD5);	   D4 GPO(PD4);
 	 * D3 GPO(PD3);	D2 GPO(PD2);	D1 GPO(PD1);	   D0 GPO(PD0);
 	 */
-	ctrl_outw(0x5555, PORT_PDCR);	/* 01 01 01 01 01 01 01 01 */
+	__raw_writew(0x5555, PORT_PDCR);	/* 01 01 01 01 01 01 01 01 */
 
 	/* E7 (x);	  E6 GPI(nu);	 E5 GPI(nu);	  E4 LCD_M_DISP;
 	 * E3 LCD_CL1;	  E2 LCD_CL2;	 E1 LCD_DON;	  E0 LCD_FLM;
 	 */
-	ctrl_outw(0x3C00, PORT_PECR);	/* 00 11 11 00 00 00 00 00 */
+	__raw_writew(0x3C00, PORT_PECR);	/* 00 11 11 00 00 00 00 00 */
 
 	/* F7 (x);	     F6 DA1(VLCD);     F5 DA0(nc);	  F4 AN3;
 	 * F3 AN2(MID_AD);   F2 AN1(EARTH_AD); F1 AN0(TEMP);	  F0 GPI+(nc);
 	 */
-	ctrl_outw(0x0002, PORT_PFCR);	/* 00 00 00 00 00 00 00 10 */
+	__raw_writew(0x0002, PORT_PFCR);	/* 00 00 00 00 00 00 00 10 */
 
 	/* G7 (x);	  G6 IRQ5(TOUCH_BUSY); G5 IRQ4(TOUCH_IRQ); G4 GPI(KEY2);
 	 * G3 GPI(KEY1);  G2 GPO(LED11);	G1 GPO(LED10);     G0 GPO(LED9);
 	 */
-	ctrl_outw(0x03D5, PORT_PGCR);	/* 00 00 00 11 11 01 01 01 */
+	__raw_writew(0x03D5, PORT_PGCR);	/* 00 00 00 11 11 01 01 01 */
 
 	/* H7 (x);	      H6 /RAS(BRAS);	  H5 /CAS(BCAS); H4 CKE(BCKE);
 	 * H3 GPO(EARTH_OFF); H2 GPO(EARTH_TEST); H1 USB2_PWR;	 H0 USB1_PWR;
 	 */
-	ctrl_outw(0x0050, PORT_PHCR);	/* 00 00 00 00 01 01 00 00 */
+	__raw_writew(0x0050, PORT_PHCR);	/* 00 00 00 00 01 01 00 00 */
 
 	/* J7 (x);	  J6 AUDCK;	   J5 ASEBRKAK;	    J4 AUDATA3;
 	 * J3 AUDATA2;	  J2 AUDATA1;	   J1 AUDATA0;	    J0 AUDSYNC;
 	 */
-	ctrl_outw(0x0000, PORT_PJCR);	/* 00 00 00 00 00 00 00 00 */
+	__raw_writew(0x0000, PORT_PJCR);	/* 00 00 00 00 00 00 00 00 */
 
 	/* K7 (x);	    K6 (x);	     K5 (x);	   K4 (x);
 	 * K3 PINT7(/PWR2); K2 PINT6(/PWR1); K1 PINT5(nu); K0 PINT4(FLASH_READY)
 	 */
-	ctrl_outw(0x00FF, PORT_PKCR);	/* 00 00 00 00 11 11 11 11 */
+	__raw_writew(0x00FF, PORT_PKCR);	/* 00 00 00 00 11 11 11 11 */
 
 	/* L7 TRST;	   L6 TMS;	     L5 TDO;		  L4 TDI;
 	 * L3 TCK;	   L2 (x);	     L1 (x);		  L0 (x);
 	 */
-	ctrl_outw(0x0000, PORT_PLCR);	/* 00 00 00 00 00 00 00 00 */
+	__raw_writew(0x0000, PORT_PLCR);	/* 00 00 00 00 00 00 00 00 */
 
 	/* M7 GPO(CURRENT_SINK);    M6 GPO(PWR_SWITCH);     M5 GPO(LAN_SPEED);
 	 * M4 GPO(LAN_RESET);       M3 GPO(BUZZER);	    M2 GPO(LCD_BL);
 	 * M1 CS5B(CAN3_CS);	    M0 GPI+(nc);
 	 */
-	ctrl_outw(0x5552, PORT_PMCR);	   /* 01 01 01 01 01 01 00 10 */
+	__raw_writew(0x5552, PORT_PMCR);	   /* 01 01 01 01 01 01 00 10 */
 
 	/* CURRENT_SINK=off,	PWR_SWITCH=off, LAN_SPEED=100MBit,
 	 * LAN_RESET=off,	BUZZER=off,	LCD_BL=off
 	 */
 #if CONFIG_SH_MAGIC_PANEL_R2_VERSION == 2
-	ctrl_outb(0x30, PORT_PMDR);
+	__raw_writeb(0x30, PORT_PMDR);
 #elif CONFIG_SH_MAGIC_PANEL_R2_VERSION == 3
-	ctrl_outb(0xF0, PORT_PMDR);
+	__raw_writeb(0xF0, PORT_PMDR);
 #else
 #error Unknown revision of PLATFORM_MP_R2
 #endif
@@ -167,8 +167,8 @@ static void __init setup_port_multiplexing(void)
 	 * P4 GPO(nu);	       P3 IRQ3(LAN_IRQ);  P2 IRQ2(CAN3_IRQ);
 	 * P1 IRQ1(CAN2_IRQ);  P0 IRQ0(CAN1_IRQ)
 	 */
-	ctrl_outw(0x0100, PORT_PPCR);	/* 00 00 00 01 00 00 00 00 */
-	ctrl_outb(0x10, PORT_PPDR);
+	__raw_writew(0x0100, PORT_PPCR);	/* 00 00 00 01 00 00 00 00 */
+	__raw_writeb(0x10, PORT_PPDR);
 
 	/* R7 A25;	     R6 A24;	     R5 A23;		  R4 A22;
 	 * R3 A21;	     R2 A20;	     R1 A19;		  R0 A0;
@@ -185,22 +185,22 @@ static void __init setup_port_multiplexing(void)
 	/* S7 (x);		S6 (x);        S5 (x);	     S4 GPO(EEPROM_CS2);
 	 * S3 GPO(EEPROM_CS1);  S2 SIOF0_TXD;  S1 SIOF0_RXD; S0 SIOF0_SCK;
 	 */
-	ctrl_outw(0x0140, PORT_PSCR);	/* 00 00 00 01 01 00 00 00 */
+	__raw_writew(0x0140, PORT_PSCR);	/* 00 00 00 01 01 00 00 00 */
 
 	/* T7 (x);	   T6 (x);	  T5 (x);	  T4 COM1_CTS;
 	 * T3 COM1_RTS;	   T2 COM1_TXD;	  T1 COM1_RXD;	  T0 GPO(WDOG)
 	 */
-	ctrl_outw(0x0001, PORT_PTCR);	/* 00 00 00 00 00 00 00 01 */
+	__raw_writew(0x0001, PORT_PTCR);	/* 00 00 00 00 00 00 00 01 */
 
 	/* U7 (x);	     U6 (x);	   U5 (x);	  U4 GPI+(/AC_FAULT);
 	 * U3 GPO(TOUCH_CS); U2 TOUCH_TXD; U1 TOUCH_RXD;  U0 TOUCH_SCK;
 	 */
-	ctrl_outw(0x0240, PORT_PUCR);	/* 00 00 00 10 01 00 00 00 */
+	__raw_writew(0x0240, PORT_PUCR);	/* 00 00 00 10 01 00 00 00 */
 
 	/* V7 (x);	  V6 (x);	V5 (x);		  V4 GPO(MID2);
 	 * V3 GPO(MID1);  V2 CARD_TxD;	V1 CARD_RxD;	  V0 GPI+(/BAT_FAULT);
 	 */
-	ctrl_outw(0x0142, PORT_PVCR);	/* 00 00 00 01 01 00 00 10 */
+	__raw_writew(0x0142, PORT_PVCR);	/* 00 00 00 01 01 00 00 10 */
 }
 
 static void __init mpr2_setup(char **cmdline_p)
@@ -209,24 +209,24 @@ static void __init mpr2_setup(char **cmdline_p)
 	 * /PCC_CD1, /PCC_CD2,  PCC_BVD1, PCC_BVD2,
 	 * /IOIS16,  IRQ4,	IRQ5,	  USB1d_SUSPEND
 	 */
-	ctrl_outw(0xAABC, PORT_PSELA);
+	__raw_writew(0xAABC, PORT_PSELA);
 	/* set Pin Select Register B:
 	 * /SCIF0_RTS, /SCIF0_CTS, LCD_VCPWC,
 	 * LCD_VEPWC,  IIC_SDA,    IIC_SCL, Reserved
 	 */
-	ctrl_outw(0x3C00, PORT_PSELB);
+	__raw_writew(0x3C00, PORT_PSELB);
 	/* set Pin Select Register C:
 	 * SIOF1_SCK, SIOF1_RxD, SCIF1_RxD, SCIF1_TxD, Reserved
 	 */
-	ctrl_outw(0x0000, PORT_PSELC);
+	__raw_writew(0x0000, PORT_PSELC);
 	/* set Pin Select Register D: Reserved, SIOF1_TxD, Reserved, SIOF1_MCLK,
 	 * Reserved, SIOF1_SYNC, Reserved, SCIF1_SCK, Reserved
 	 */
-	ctrl_outw(0x0000, PORT_PSELD);
+	__raw_writew(0x0000, PORT_PSELD);
 	/* set USB TxRx Control: Reserved, DRV, Reserved, USB_TRANS, USB_SEL */
-	ctrl_outw(0x0101, PORT_UTRCTL);
+	__raw_writew(0x0101, PORT_UTRCTL);
 	/* set USB Clock Control: USSCS, USSTB, Reserved (HighByte always A5) */
-	ctrl_outw(0xA5C0, PORT_UCLKCR_W);
+	__raw_writew(0xA5C0, PORT_UCLKCR_W);
 
 	setup_chip_select();
 
diff --git a/arch/sh/boards/board-polaris.c b/arch/sh/boards/board-polaris.c
index 5bc1269..5948663 100644
--- a/arch/sh/boards/board-polaris.c
+++ b/arch/sh/boards/board-polaris.c
@@ -89,15 +89,15 @@ static int __init polaris_initialise(void)
 	printk(KERN_INFO "Configuring Polaris external bus\n");
 
 	/* Configure area 5 with 2 wait states */
-	wcr = ctrl_inw(WCR2);
+	wcr = __raw_readw(WCR2);
 	wcr &= (~AREA5_WAIT_CTRL);
 	wcr |= (WAIT_STATES_10 << 10);
-	ctrl_outw(wcr, WCR2);
+	__raw_writew(wcr, WCR2);
 
 	/* Configure area 5 for 32-bit access */
-	bcr_mask = ctrl_inw(BCR2);
+	bcr_mask = __raw_readw(BCR2);
 	bcr_mask |= 1 << 10;
-	ctrl_outw(bcr_mask, BCR2);
+	__raw_writew(bcr_mask, BCR2);
 
 	return platform_add_devices(polaris_devices,
 				    ARRAY_SIZE(polaris_devices));
@@ -128,13 +128,13 @@ static struct ipr_desc ipr_irq_desc = {
 static void __init init_polaris_irq(void)
 {
 	/* Disable all interrupts */
-	ctrl_outw(0, BCR_ILCRA);
-	ctrl_outw(0, BCR_ILCRB);
-	ctrl_outw(0, BCR_ILCRC);
-	ctrl_outw(0, BCR_ILCRD);
-	ctrl_outw(0, BCR_ILCRE);
-	ctrl_outw(0, BCR_ILCRF);
-	ctrl_outw(0, BCR_ILCRG);
+	__raw_writew(0, BCR_ILCRA);
+	__raw_writew(0, BCR_ILCRB);
+	__raw_writew(0, BCR_ILCRC);
+	__raw_writew(0, BCR_ILCRD);
+	__raw_writew(0, BCR_ILCRE);
+	__raw_writew(0, BCR_ILCRF);
+	__raw_writew(0, BCR_ILCRG);
 
 	register_ipr_controller(&ipr_irq_desc);
 }
diff --git a/arch/sh/boards/board-shmin.c b/arch/sh/boards/board-shmin.c
index b1dcbbc..325bed5 100644
--- a/arch/sh/boards/board-shmin.c
+++ b/arch/sh/boards/board-shmin.c
@@ -17,8 +17,8 @@
 
 static void __init init_shmin_irq(void)
 {
-	ctrl_outw(0x2a00, PFC_PHCR);	// IRQ0-3=IRQ
-	ctrl_outw(0x0aaa, INTC_ICR1);	// IRQ0-3=IRQ-mode,Low-active.
+	__raw_writew(0x2a00, PFC_PHCR);	// IRQ0-3=IRQ
+	__raw_writew(0x0aaa, INTC_ICR1);	// IRQ0-3=IRQ-mode,Low-active.
 	plat_irq_setup_pins(IRQ_MODE_IRQ);
 }
 
diff --git a/arch/sh/boards/mach-ap325rxa/setup.c b/arch/sh/boards/mach-ap325rxa/setup.c
index 1f5fa5c..27277cb 100644
--- a/arch/sh/boards/mach-ap325rxa/setup.c
+++ b/arch/sh/boards/mach-ap325rxa/setup.c
@@ -159,21 +159,21 @@ static void ap320_wvga_power_on(void *board_data)
 	msleep(100);
 
 	/* ASD AP-320/325 LCD ON */
-	ctrl_outw(FPGA_LCDREG_VAL, FPGA_LCDREG);
+	__raw_writew(FPGA_LCDREG_VAL, FPGA_LCDREG);
 
 	/* backlight */
 	gpio_set_value(GPIO_PTS3, 0);
-	ctrl_outw(0x100, FPGA_BKLREG);
+	__raw_writew(0x100, FPGA_BKLREG);
 }
 
 static void ap320_wvga_power_off(void *board_data)
 {
 	/* backlight */
-	ctrl_outw(0, FPGA_BKLREG);
+	__raw_writew(0, FPGA_BKLREG);
 	gpio_set_value(GPIO_PTS3, 1);
 
 	/* ASD AP-320/325 LCD OFF */
-	ctrl_outw(0, FPGA_LCDREG);
+	__raw_writew(0, FPGA_LCDREG);
 }
 
 static struct sh_mobile_lcdc_info lcdc_info = {
@@ -595,7 +595,7 @@ static int __init ap325rxa_devices_setup(void)
 	gpio_request(GPIO_PTZ4, NULL);
 	gpio_direction_output(GPIO_PTZ4, 0); /* SADDR */
 
-	ctrl_outw(ctrl_inw(PORT_MSELCRB) & ~0x0001, PORT_MSELCRB);
+	__raw_writew(__raw_readw(PORT_MSELCRB) & ~0x0001, PORT_MSELCRB);
 
 	/* FLCTL */
 	gpio_request(GPIO_FN_FCE, NULL);
@@ -613,9 +613,9 @@ static int __init ap325rxa_devices_setup(void)
 	gpio_request(GPIO_FN_FWE, NULL);
 	gpio_request(GPIO_FN_FRB, NULL);
 
-	ctrl_outw(0, PORT_HIZCRC);
-	ctrl_outw(0xFFFF, PORT_DRVCRA);
-	ctrl_outw(0xFFFF, PORT_DRVCRB);
+	__raw_writew(0, PORT_HIZCRC);
+	__raw_writew(0xFFFF, PORT_DRVCRA);
+	__raw_writew(0xFFFF, PORT_DRVCRB);
 
 	platform_resource_setup_memory(&ceu_device, "ceu", 4 << 20);
 
diff --git a/arch/sh/boards/mach-cayman/irq.c b/arch/sh/boards/mach-cayman/irq.c
index 33f7708..1394b07 100644
--- a/arch/sh/boards/mach-cayman/irq.c
+++ b/arch/sh/boards/mach-cayman/irq.c
@@ -66,9 +66,9 @@ static void enable_cayman_irq(unsigned int irq)
 	reg = EPLD_MASK_BASE + ((irq / 8) << 2);
 	bit = 1<<(irq % 8);
 	local_irq_save(flags);
-	mask = ctrl_inl(reg);
+	mask = __raw_readl(reg);
 	mask |= bit;
-	ctrl_outl(mask, reg);
+	__raw_writel(mask, reg);
 	local_irq_restore(flags);
 }
 
@@ -83,9 +83,9 @@ void disable_cayman_irq(unsigned int irq)
 	reg = EPLD_MASK_BASE + ((irq / 8) << 2);
 	bit = 1<<(irq % 8);
 	local_irq_save(flags);
-	mask = ctrl_inl(reg);
+	mask = __raw_readl(reg);
 	mask &= ~bit;
-	ctrl_outl(mask, reg);
+	__raw_writel(mask, reg);
 	local_irq_restore(flags);
 }
 
@@ -109,8 +109,8 @@ int cayman_irq_demux(int evt)
 		unsigned long status;
 		int i;
 
-		status = ctrl_inl(EPLD_STATUS_BASE) &
-			 ctrl_inl(EPLD_MASK_BASE) & 0xff;
+		status = __raw_readl(EPLD_STATUS_BASE) &
+			 __raw_readl(EPLD_MASK_BASE) & 0xff;
 		if (status == 0) {
 			irq = -1;
 		} else {
@@ -126,8 +126,8 @@ int cayman_irq_demux(int evt)
 		unsigned long status;
 		int i;
 
-		status = ctrl_inl(EPLD_STATUS_BASE + 3 * sizeof(u32)) &
-			 ctrl_inl(EPLD_MASK_BASE + 3 * sizeof(u32)) & 0xff;
+		status = __raw_readl(EPLD_STATUS_BASE + 3 * sizeof(u32)) &
+			 __raw_readl(EPLD_MASK_BASE + 3 * sizeof(u32)) & 0xff;
 		if (status == 0) {
 			irq = -1;
 		} else {
diff --git a/arch/sh/boards/mach-dreamcast/rtc.c b/arch/sh/boards/mach-dreamcast/rtc.c
index a743368..061d657 100644
--- a/arch/sh/boards/mach-dreamcast/rtc.c
+++ b/arch/sh/boards/mach-dreamcast/rtc.c
@@ -35,11 +35,11 @@ static void aica_rtc_gettimeofday(struct timespec *ts)
 	unsigned long val1, val2;
 
 	do {
-		val1 = ((ctrl_inl(AICA_RTC_SECS_H) & 0xffff) << 16) |
-			(ctrl_inl(AICA_RTC_SECS_L) & 0xffff);
+		val1 = ((__raw_readl(AICA_RTC_SECS_H) & 0xffff) << 16) |
+			(__raw_readl(AICA_RTC_SECS_L) & 0xffff);
 
-		val2 = ((ctrl_inl(AICA_RTC_SECS_H) & 0xffff) << 16) |
-			(ctrl_inl(AICA_RTC_SECS_L) & 0xffff);
+		val2 = ((__raw_readl(AICA_RTC_SECS_H) & 0xffff) << 16) |
+			(__raw_readl(AICA_RTC_SECS_L) & 0xffff);
 	} while (val1 != val2);
 
 	ts->tv_sec = val1 - TWENTY_YEARS;
@@ -60,14 +60,14 @@ static int aica_rtc_settimeofday(const time_t secs)
 	unsigned long adj = secs + TWENTY_YEARS;
 
 	do {
-		ctrl_outl((adj & 0xffff0000) >> 16, AICA_RTC_SECS_H);
-		ctrl_outl((adj & 0xffff), AICA_RTC_SECS_L);
+		__raw_writel((adj & 0xffff0000) >> 16, AICA_RTC_SECS_H);
+		__raw_writel((adj & 0xffff), AICA_RTC_SECS_L);
 
-		val1 = ((ctrl_inl(AICA_RTC_SECS_H) & 0xffff) << 16) |
-			(ctrl_inl(AICA_RTC_SECS_L) & 0xffff);
+		val1 = ((__raw_readl(AICA_RTC_SECS_H) & 0xffff) << 16) |
+			(__raw_readl(AICA_RTC_SECS_L) & 0xffff);
 
-		val2 = ((ctrl_inl(AICA_RTC_SECS_H) & 0xffff) << 16) |
-			(ctrl_inl(AICA_RTC_SECS_L) & 0xffff);
+		val2 = ((__raw_readl(AICA_RTC_SECS_H) & 0xffff) << 16) |
+			(__raw_readl(AICA_RTC_SECS_L) & 0xffff);
 	} while (val1 != val2);
 
 	return 0;
diff --git a/arch/sh/boards/mach-ecovec24/setup.c b/arch/sh/boards/mach-ecovec24/setup.c
index a49cce1..1135c3b 100644
--- a/arch/sh/boards/mach-ecovec24/setup.c
+++ b/arch/sh/boards/mach-ecovec24/setup.c
@@ -696,13 +696,13 @@ static struct platform_device camera_devices[] = {
 #define FCLKBCR		0xa415000c
 static void fsimck_init(struct clk *clk)
 {
-	u32 status = ctrl_inl(clk->enable_reg);
+	u32 status = __raw_readl(clk->enable_reg);
 
 	/* use external clock */
 	status &= ~0x000000ff;
 	status |= 0x00000080;
 
-	ctrl_outl(status, clk->enable_reg);
+	__raw_writel(status, clk->enable_reg);
 }
 
 static struct clk_ops fsimck_clk_ops = {
@@ -853,7 +853,7 @@ static int __init arch_setup(void)
 	gpio_direction_output(GPIO_PTG1, 0);
 	gpio_direction_output(GPIO_PTG2, 0);
 	gpio_direction_output(GPIO_PTG3, 0);
-	ctrl_outw((ctrl_inw(PORT_HIZA) & ~(0x1 << 1)) , PORT_HIZA);
+	__raw_writew((__raw_readw(PORT_HIZA) & ~(0x1 << 1)) , PORT_HIZA);
 
 	/* enable SH-Eth */
 	gpio_request(GPIO_PTA1, NULL);
@@ -873,16 +873,16 @@ static int __init arch_setup(void)
 	gpio_request(GPIO_FN_LNKSTA,       NULL);
 
 	/* enable USB */
-	ctrl_outw(0x0000, 0xA4D80000);
-	ctrl_outw(0x0000, 0xA4D90000);
+	__raw_writew(0x0000, 0xA4D80000);
+	__raw_writew(0x0000, 0xA4D90000);
 	gpio_request(GPIO_PTB3,  NULL);
 	gpio_request(GPIO_PTB4,  NULL);
 	gpio_request(GPIO_PTB5,  NULL);
 	gpio_direction_input(GPIO_PTB3);
 	gpio_direction_output(GPIO_PTB4, 0);
 	gpio_direction_output(GPIO_PTB5, 0);
-	ctrl_outw(0x0600, 0xa40501d4);
-	ctrl_outw(0x0600, 0xa4050192);
+	__raw_writew(0x0600, 0xa40501d4);
+	__raw_writew(0x0600, 0xa4050192);
 
 	if (gpio_get_value(GPIO_PTB3)) {
 		printk(KERN_INFO "USB1 function is selected\n");
@@ -923,7 +923,7 @@ static int __init arch_setup(void)
 	gpio_request(GPIO_FN_LCDVSYN,  NULL);
 	gpio_request(GPIO_FN_LCDDON,   NULL);
 	gpio_request(GPIO_FN_LCDLCLK,  NULL);
-	ctrl_outw((ctrl_inw(PORT_HIZA) & ~0x0001), PORT_HIZA);
+	__raw_writew((__raw_readw(PORT_HIZA) & ~0x0001), PORT_HIZA);
 
 	gpio_request(GPIO_PTE6, NULL);
 	gpio_request(GPIO_PTU1, NULL);
@@ -935,7 +935,7 @@ static int __init arch_setup(void)
 	gpio_direction_output(GPIO_PTA2, 0);
 
 	/* I/O buffer drive ability is high */
-	ctrl_outw((ctrl_inw(IODRIVEA) & ~0x00c0) | 0x0080 , IODRIVEA);
+	__raw_writew((__raw_readw(IODRIVEA) & ~0x00c0) | 0x0080 , IODRIVEA);
 
 	if (gpio_get_value(GPIO_PTE6)) {
 		/* DVI */
@@ -1067,7 +1067,7 @@ static int __init arch_setup(void)
 	gpio_direction_output(GPIO_PTB7, 0);
 
 	/* I/O buffer drive ability is high for SDHI1 */
-	ctrl_outw((ctrl_inw(IODRIVEA) & ~0x3000) | 0x2000 , IODRIVEA);
+	__raw_writew((__raw_readw(IODRIVEA) & ~0x3000) | 0x2000 , IODRIVEA);
 #else
 	/* enable MSIOF0 on CN11 (needs DS2.4 set to OFF) */
 	gpio_request(GPIO_FN_MSIOF0_TXD, NULL);
diff --git a/arch/sh/boards/mach-highlander/irq-r7780mp.c b/arch/sh/boards/mach-highlander/irq-r7780mp.c
index 83c28bc..9893fd3 100644
--- a/arch/sh/boards/mach-highlander/irq-r7780mp.c
+++ b/arch/sh/boards/mach-highlander/irq-r7780mp.c
@@ -64,7 +64,7 @@ static DECLARE_INTC_DESC(intc_desc, "r7780mp", vectors,
 
 unsigned char * __init highlander_plat_irq_setup(void)
 {
-	if ((ctrl_inw(0xa4000700) & 0xf000) == 0x2000) {
+	if ((__raw_readw(0xa4000700) & 0xf000) == 0x2000) {
 		printk(KERN_INFO "Using r7780mp interrupt controller.\n");
 		register_intc_controller(&intc_desc);
 		return irl2irq;
diff --git a/arch/sh/boards/mach-highlander/irq-r7780rp.c b/arch/sh/boards/mach-highlander/irq-r7780rp.c
index b721e86..0805b21 100644
--- a/arch/sh/boards/mach-highlander/irq-r7780rp.c
+++ b/arch/sh/boards/mach-highlander/irq-r7780rp.c
@@ -57,7 +57,7 @@ static DECLARE_INTC_DESC(intc_desc, "r7780rp", vectors,
 
 unsigned char * __init highlander_plat_irq_setup(void)
 {
-	if (ctrl_inw(0xa5000600)) {
+	if (__raw_readw(0xa5000600)) {
 		printk(KERN_INFO "Using r7780rp interrupt controller.\n");
 		register_intc_controller(&intc_desc);
 		return irl2irq;
diff --git a/arch/sh/boards/mach-highlander/irq-r7785rp.c b/arch/sh/boards/mach-highlander/irq-r7785rp.c
index 3811b06..558b248 100644
--- a/arch/sh/boards/mach-highlander/irq-r7785rp.c
+++ b/arch/sh/boards/mach-highlander/irq-r7785rp.c
@@ -66,20 +66,20 @@ static DECLARE_INTC_DESC(intc_desc, "r7785rp", vectors,
 
 unsigned char * __init highlander_plat_irq_setup(void)
 {
-	if ((ctrl_inw(0xa4000158) & 0xf000) != 0x1000)
+	if ((__raw_readw(0xa4000158) & 0xf000) != 0x1000)
 		return NULL;
 
 	printk(KERN_INFO "Using r7785rp interrupt controller.\n");
 
-	ctrl_outw(0x0000, PA_IRLSSR1);	/* FPGA IRLSSR1(CF_CD clear) */
+	__raw_writew(0x0000, PA_IRLSSR1);	/* FPGA IRLSSR1(CF_CD clear) */
 
 	/* Setup the FPGA IRL */
-	ctrl_outw(0x0000, PA_IRLPRA);	/* FPGA IRLA */
-	ctrl_outw(0xe598, PA_IRLPRB);	/* FPGA IRLB */
-	ctrl_outw(0x7060, PA_IRLPRC);	/* FPGA IRLC */
-	ctrl_outw(0x0000, PA_IRLPRD);	/* FPGA IRLD */
-	ctrl_outw(0x4321, PA_IRLPRE);	/* FPGA IRLE */
-	ctrl_outw(0xdcba, PA_IRLPRF);	/* FPGA IRLF */
+	__raw_writew(0x0000, PA_IRLPRA);	/* FPGA IRLA */
+	__raw_writew(0xe598, PA_IRLPRB);	/* FPGA IRLB */
+	__raw_writew(0x7060, PA_IRLPRC);	/* FPGA IRLC */
+	__raw_writew(0x0000, PA_IRLPRD);	/* FPGA IRLD */
+	__raw_writew(0x4321, PA_IRLPRE);	/* FPGA IRLE */
+	__raw_writew(0xdcba, PA_IRLPRF);	/* FPGA IRLF */
 
 	register_intc_controller(&intc_desc);
 	return irl2irq;
diff --git a/arch/sh/boards/mach-highlander/psw.c b/arch/sh/boards/mach-highlander/psw.c
index 37b1a2e..5227863 100644
--- a/arch/sh/boards/mach-highlander/psw.c
+++ b/arch/sh/boards/mach-highlander/psw.c
@@ -24,7 +24,7 @@ static irqreturn_t psw_irq_handler(int irq, void *arg)
 	unsigned int l, mask;
 	int ret = 0;
 
-	l = ctrl_inw(PA_DBSW);
+	l = __raw_readw(PA_DBSW);
 
 	/* Nothing to do if there's no state change */
 	if (psw->state) {
@@ -45,7 +45,7 @@ static irqreturn_t psw_irq_handler(int irq, void *arg)
 out:
 	/* Clear the switch IRQs */
 	l |= (0x7 << 12);
-	ctrl_outw(l, PA_DBSW);
+	__raw_writew(l, PA_DBSW);
 
 	return IRQ_RETVAL(ret);
 }
diff --git a/arch/sh/boards/mach-highlander/setup.c b/arch/sh/boards/mach-highlander/setup.c
index f663c14..affd667 100644
--- a/arch/sh/boards/mach-highlander/setup.c
+++ b/arch/sh/boards/mach-highlander/setup.c
@@ -311,13 +311,13 @@ device_initcall(r7780rp_devices_setup);
  */
 static int ivdr_clk_enable(struct clk *clk)
 {
-	ctrl_outw(ctrl_inw(PA_IVDRCTL) | (1 << IVDR_CK_ON), PA_IVDRCTL);
+	__raw_writew(__raw_readw(PA_IVDRCTL) | (1 << IVDR_CK_ON), PA_IVDRCTL);
 	return 0;
 }
 
 static void ivdr_clk_disable(struct clk *clk)
 {
-	ctrl_outw(ctrl_inw(PA_IVDRCTL) & ~(1 << IVDR_CK_ON), PA_IVDRCTL);
+	__raw_writew(__raw_readw(PA_IVDRCTL) & ~(1 << IVDR_CK_ON), PA_IVDRCTL);
 }
 
 static struct clk_ops ivdr_clk_ops = {
@@ -337,7 +337,7 @@ static struct clk *r7780rp_clocks[] = {
 static void r7780rp_power_off(void)
 {
 	if (mach_is_r7780mp() || mach_is_r7785rp())
-		ctrl_outw(0x0001, PA_POFF);
+		__raw_writew(0x0001, PA_POFF);
 }
 
 /*
@@ -345,7 +345,7 @@ static void r7780rp_power_off(void)
  */
 static void __init highlander_setup(char **cmdline_p)
 {
-	u16 ver = ctrl_inw(PA_VERREG);
+	u16 ver = __raw_readw(PA_VERREG);
 	int i;
 
 	printk(KERN_INFO "Renesas Solutions Highlander %s support.\n",
@@ -370,12 +370,12 @@ static void __init highlander_setup(char **cmdline_p)
 		clk_enable(clk);
 	}
 
-	ctrl_outw(0x0000, PA_OBLED);	/* Clear LED. */
+	__raw_writew(0x0000, PA_OBLED);	/* Clear LED. */
 
 	if (mach_is_r7780rp())
-		ctrl_outw(0x0001, PA_SDPOW);	/* SD Power ON */
+		__raw_writew(0x0001, PA_SDPOW);	/* SD Power ON */
 
-	ctrl_outw(ctrl_inw(PA_IVDRCTL) | 0x01, PA_IVDRCTL);	/* Si13112 */
+	__raw_writew(__raw_readw(PA_IVDRCTL) | 0x01, PA_IVDRCTL);	/* Si13112 */
 
 	pm_power_off = r7780rp_power_off;
 }
diff --git a/arch/sh/boards/mach-hp6xx/hp6xx_apm.c b/arch/sh/boards/mach-hp6xx/hp6xx_apm.c
index e85212f..b49535c 100644
--- a/arch/sh/boards/mach-hp6xx/hp6xx_apm.c
+++ b/arch/sh/boards/mach-hp6xx/hp6xx_apm.c
@@ -53,7 +53,7 @@ static void hp6x0_apm_get_power_status(struct apm_power_info *info)
 	info->ac_line_status = (battery > HP680_BATTERY_AC_ON) ?
 			 APM_AC_ONLINE : APM_AC_OFFLINE;
 
-	pgdr = ctrl_inb(PGDR);
+	pgdr = __raw_readb(PGDR);
 	if (pgdr & PGDR_MAIN_BATTERY_OUT) {
 		info->battery_status	= APM_BATTERY_STATUS_NOT_PRESENT;
 		info->battery_flag	= 0x80;
diff --git a/arch/sh/boards/mach-hp6xx/pm.c b/arch/sh/boards/mach-hp6xx/pm.c
index d936c1a..4499a37 100644
--- a/arch/sh/boards/mach-hp6xx/pm.c
+++ b/arch/sh/boards/mach-hp6xx/pm.c
@@ -53,17 +53,17 @@ static void pm_enter(void)
 	sh_wdt_write_cnt(0);
 
 	/* disable PLL1 */
-	frqcr = ctrl_inw(FRQCR);
+	frqcr = __raw_readw(FRQCR);
 	frqcr &= ~(FRQCR_PLLEN | FRQCR_PSTBY);
-	ctrl_outw(frqcr, FRQCR);
+	__raw_writew(frqcr, FRQCR);
 
 	/* enable standby */
-	stbcr = ctrl_inb(STBCR);
-	ctrl_outb(stbcr | STBCR_STBY | STBCR_MSTP2, STBCR);
+	stbcr = __raw_readb(STBCR);
+	__raw_writeb(stbcr | STBCR_STBY | STBCR_MSTP2, STBCR);
 
 	/* set self-refresh */
-	mcr = ctrl_inw(MCR);
-	ctrl_outw(mcr & ~MCR_RFSH, MCR);
+	mcr = __raw_readw(MCR);
+	__raw_writew(mcr & ~MCR_RFSH, MCR);
 
 	/* set interrupt handler */
 	asm volatile("stc vbr, %0" : "=r" (vbr_old));
@@ -73,8 +73,8 @@ static void pm_enter(void)
 	       &wakeup_start, &wakeup_end - &wakeup_start);
 	asm volatile("ldc %0, vbr" : : "r" (vbr_new));
 
-	ctrl_outw(0, RTCNT);
-	ctrl_outw(mcr | MCR_RFSH | MCR_RMODE, MCR);
+	__raw_writew(0, RTCNT);
+	__raw_writew(mcr | MCR_RFSH | MCR_RMODE, MCR);
 
 	cpu_sleep();
 
@@ -83,14 +83,14 @@ static void pm_enter(void)
 	free_page(vbr_new);
 
 	/* enable PLL1 */
-	frqcr = ctrl_inw(FRQCR);
+	frqcr = __raw_readw(FRQCR);
 	frqcr |= FRQCR_PSTBY;
-	ctrl_outw(frqcr, FRQCR);
+	__raw_writew(frqcr, FRQCR);
 	udelay(50);
 	frqcr |= FRQCR_PLLEN;
-	ctrl_outw(frqcr, FRQCR);
+	__raw_writew(frqcr, FRQCR);
 
-	ctrl_outb(stbcr, STBCR);
+	__raw_writeb(stbcr, STBCR);
 
 	clear_bl_bit();
 }
@@ -115,21 +115,21 @@ static int hp6x0_pm_enter(suspend_state_t state)
 	outw(hd64461_stbcr, HD64461_STBCR);
 #endif
 
-	ctrl_outb(0x1f, DACR);
+	__raw_writeb(0x1f, DACR);
 
-	stbcr = ctrl_inb(STBCR);
-	ctrl_outb(0x01, STBCR);
+	stbcr = __raw_readb(STBCR);
+	__raw_writeb(0x01, STBCR);
 
-	stbcr2 = ctrl_inb(STBCR2);
-	ctrl_outb(0x7f , STBCR2);
+	stbcr2 = __raw_readb(STBCR2);
+	__raw_writeb(0x7f , STBCR2);
 
 	outw(0xf07f, HD64461_SCPUCR);
 
 	pm_enter();
 
 	outw(0, HD64461_SCPUCR);
-	ctrl_outb(stbcr, STBCR);
-	ctrl_outb(stbcr2, STBCR2);
+	__raw_writeb(stbcr, STBCR);
+	__raw_writeb(stbcr2, STBCR2);
 
 #ifdef CONFIG_HD64461_ENABLER
 	hd64461_stbcr = inw(HD64461_STBCR);
diff --git a/arch/sh/boards/mach-hp6xx/setup.c b/arch/sh/boards/mach-hp6xx/setup.c
index e6dd5e9..8c9add5 100644
--- a/arch/sh/boards/mach-hp6xx/setup.c
+++ b/arch/sh/boards/mach-hp6xx/setup.c
@@ -149,19 +149,19 @@ static void __init hp6xx_setup(char **cmdline_p)
 
 	sh_dac_output(0, DAC_SPEAKER_VOLUME);
 	sh_dac_disable(DAC_SPEAKER_VOLUME);
-	v8 = ctrl_inb(DACR);
+	v8 = __raw_readb(DACR);
 	v8 &= ~DACR_DAE;
-	ctrl_outb(v8,DACR);
+	__raw_writeb(v8,DACR);
 
-	v8 = ctrl_inb(SCPDR);
+	v8 = __raw_readb(SCPDR);
 	v8 |= SCPDR_TS_SCAN_X | SCPDR_TS_SCAN_Y;
 	v8 &= ~SCPDR_TS_SCAN_ENABLE;
-	ctrl_outb(v8, SCPDR);
+	__raw_writeb(v8, SCPDR);
 
-	v = ctrl_inw(SCPCR);
+	v = __raw_readw(SCPCR);
 	v &= ~SCPCR_TS_MASK;
 	v |= SCPCR_TS_ENABLE;
-	ctrl_outw(v, SCPCR);
+	__raw_writew(v, SCPCR);
 }
 device_initcall(hp6xx_devices_setup);
 
diff --git a/arch/sh/boards/mach-kfr2r09/setup.c b/arch/sh/boards/mach-kfr2r09/setup.c
index 5d7b5d9..ca9e82d 100644
--- a/arch/sh/boards/mach-kfr2r09/setup.c
+++ b/arch/sh/boards/mach-kfr2r09/setup.c
@@ -282,7 +282,7 @@ static int camera_power(struct device *dev, int mode)
 		 * use 1.8 V for VccQ_VIO
 		 * use 2.85V for VccQ_SR
 		 */
-		ctrl_outw((ctrl_inw(DRVCRB) & ~0x0003) | 0x0001, DRVCRB);
+		__raw_writew((__raw_readw(DRVCRB) & ~0x0003) | 0x0001, DRVCRB);
 
 		/* reset clear */
 		ret = gpio_request(GPIO_PTB4, NULL);
@@ -492,13 +492,13 @@ static int kfr2r09_usb0_gadget_setup(void)
 	if (kfr2r09_usb0_gadget_i2c_setup() != 0)
 		return -ENODEV; /* unable to configure using i2c */
 
-	ctrl_outw((ctrl_inw(PORT_MSELCRB) & ~0xc000) | 0x8000, PORT_MSELCRB);
+	__raw_writew((__raw_readw(PORT_MSELCRB) & ~0xc000) | 0x8000, PORT_MSELCRB);
 	gpio_request(GPIO_FN_PDSTATUS, NULL); /* R-standby disables USB clock */
 	gpio_request(GPIO_PTV6, NULL); /* USBCLK_ON */
 	gpio_direction_output(GPIO_PTV6, 1); /* USBCLK_ON = H */
 	msleep(20); /* wait 20ms to let the clock settle */
 	clk_enable(clk_get(NULL, "usb0"));
-	ctrl_outw(0x0600, 0xa40501d4);
+	__raw_writew(0x0600, 0xa40501d4);
 
 	return 0;
 }
@@ -526,12 +526,12 @@ static int __init kfr2r09_devices_setup(void)
 	gpio_direction_output(GPIO_PTG3, 1); /* HPON_ON = H */
 
 	/* setup NOR flash at CS0 */
-	ctrl_outl(0x36db0400, BSC_CS0BCR);
-	ctrl_outl(0x00000500, BSC_CS0WCR);
+	__raw_writel(0x36db0400, BSC_CS0BCR);
+	__raw_writel(0x00000500, BSC_CS0WCR);
 
 	/* setup NAND flash at CS4 */
-	ctrl_outl(0x36db0400, BSC_CS4BCR);
-	ctrl_outl(0x00000500, BSC_CS4WCR);
+	__raw_writel(0x36db0400, BSC_CS4BCR);
+	__raw_writel(0x00000500, BSC_CS4WCR);
 
 	/* setup KEYSC pins */
 	gpio_request(GPIO_FN_KEYOUT0, NULL);
diff --git a/arch/sh/boards/mach-landisk/gio.c b/arch/sh/boards/mach-landisk/gio.c
index 5280131..01e6abb 100644
--- a/arch/sh/boards/mach-landisk/gio.c
+++ b/arch/sh/boards/mach-landisk/gio.c
@@ -76,39 +76,39 @@ static long gio_ioctl(struct file *filp, unsigned int cmd, unsigned long arg)
 		break;
 
 	case GIODRV_IOCSGIODATA1:	/* write byte */
-		ctrl_outb((unsigned char)(0x0ff & data), addr);
+		__raw_writeb((unsigned char)(0x0ff & data), addr);
 		break;
 
 	case GIODRV_IOCSGIODATA2:	/* write word */
 		if (addr & 0x01) {
 			return -EFAULT;
 		}
-		ctrl_outw((unsigned short int)(0x0ffff & data), addr);
+		__raw_writew((unsigned short int)(0x0ffff & data), addr);
 		break;
 
 	case GIODRV_IOCSGIODATA4:	/* write long */
 		if (addr & 0x03) {
 			return -EFAULT;
 		}
-		ctrl_outl(data, addr);
+		__raw_writel(data, addr);
 		break;
 
 	case GIODRV_IOCGGIODATA1:	/* read byte */
-		data = ctrl_inb(addr);
+		data = __raw_readb(addr);
 		break;
 
 	case GIODRV_IOCGGIODATA2:	/* read word */
 		if (addr & 0x01) {
 			return -EFAULT;
 		}
-		data = ctrl_inw(addr);
+		data = __raw_readw(addr);
 		break;
 
 	case GIODRV_IOCGGIODATA4:	/* read long */
 		if (addr & 0x03) {
 			return -EFAULT;
 		}
-		data = ctrl_inl(addr);
+		data = __raw_readl(addr);
 		break;
 	default:
 		return -EFAULT;
diff --git a/arch/sh/boards/mach-landisk/irq.c b/arch/sh/boards/mach-landisk/irq.c
index 7b284cd..96f38a4 100644
--- a/arch/sh/boards/mach-landisk/irq.c
+++ b/arch/sh/boards/mach-landisk/irq.c
@@ -22,14 +22,14 @@ static void disable_landisk_irq(unsigned int irq)
 {
 	unsigned char mask = 0xff ^ (0x01 << (irq - 5));
 
-	ctrl_outb(ctrl_inb(PA_IMASK) & mask, PA_IMASK);
+	__raw_writeb(__raw_readb(PA_IMASK) & mask, PA_IMASK);
 }
 
 static void enable_landisk_irq(unsigned int irq)
 {
 	unsigned char value = (0x01 << (irq - 5));
 
-	ctrl_outb(ctrl_inb(PA_IMASK) | value, PA_IMASK);
+	__raw_writeb(__raw_readb(PA_IMASK) | value, PA_IMASK);
 }
 
 static struct irq_chip landisk_irq_chip __read_mostly = {
@@ -52,5 +52,5 @@ void __init init_landisk_IRQ(void)
 					      handle_level_irq, "level");
 		enable_landisk_irq(i);
 	}
-	ctrl_outb(0x00, PA_PWRINT_CLR);
+	__raw_writeb(0x00, PA_PWRINT_CLR);
 }
diff --git a/arch/sh/boards/mach-landisk/psw.c b/arch/sh/boards/mach-landisk/psw.c
index e6b0efa..bef8352 100644
--- a/arch/sh/boards/mach-landisk/psw.c
+++ b/arch/sh/boards/mach-landisk/psw.c
@@ -25,7 +25,7 @@ static irqreturn_t psw_irq_handler(int irq, void *arg)
 	unsigned int sw_value;
 	int ret = 0;
 
-	sw_value = (0x0ff & (~ctrl_inb(PA_STATUS)));
+	sw_value = (0x0ff & (~__raw_readb(PA_STATUS)));
 
 	/* Nothing to do if there's no state change */
 	if (psw->state) {
@@ -42,7 +42,7 @@ static irqreturn_t psw_irq_handler(int irq, void *arg)
 
 out:
 	/* Clear the switch IRQs */
-	ctrl_outb(0x00, PA_PWRINT_CLR);
+	__raw_writeb(0x00, PA_PWRINT_CLR);
 
 	return IRQ_RETVAL(ret);
 }
diff --git a/arch/sh/boards/mach-landisk/setup.c b/arch/sh/boards/mach-landisk/setup.c
index 2d09d4d..50337acc 100644
--- a/arch/sh/boards/mach-landisk/setup.c
+++ b/arch/sh/boards/mach-landisk/setup.c
@@ -25,7 +25,7 @@ void init_landisk_IRQ(void);
 
 static void landisk_power_off(void)
 {
-        ctrl_outb(0x01, PA_SHUTDOWN);
+        __raw_writeb(0x01, PA_SHUTDOWN);
 }
 
 static struct resource cf_ide_resources[3];
@@ -88,7 +88,7 @@ __initcall(landisk_devices_setup);
 static void __init landisk_setup(char **cmdline_p)
 {
         /* LED ON */
-	ctrl_outb(ctrl_inb(PA_LED) | 0x03, PA_LED);
+	__raw_writeb(__raw_readb(PA_LED) | 0x03, PA_LED);
 
 	printk(KERN_INFO "I-O DATA DEVICE, INC. \"LANDISK Series\" support.\n");
 	pm_power_off = landisk_power_off;
diff --git a/arch/sh/boards/mach-microdev/io.c b/arch/sh/boards/mach-microdev/io.c
index 52dd748..2960c65 100644
--- a/arch/sh/boards/mach-microdev/io.c
+++ b/arch/sh/boards/mach-microdev/io.c
@@ -141,10 +141,10 @@ static inline void delay(void)
 #if defined(CONFIG_PCI)
 	/* System board present, just make a dummy SRAM access.  (CS0 will be
 	   mapped to PCI memory, probably good to avoid it.) */
-	ctrl_inw(0xa6800000);
+	__raw_readw(0xa6800000);
 #else
 	/* CS0 will be mapped to flash, ROM etc so safe to access it. */
-	ctrl_inw(0xa0000000);
+	__raw_readw(0xa0000000);
 #endif
 }
 
diff --git a/arch/sh/boards/mach-microdev/irq.c b/arch/sh/boards/mach-microdev/irq.c
index b551963..a26d166 100644
--- a/arch/sh/boards/mach-microdev/irq.c
+++ b/arch/sh/boards/mach-microdev/irq.c
@@ -88,7 +88,7 @@ static void disable_microdev_irq(unsigned int irq)
 	fpgaIrq = fpgaIrqTable[irq].fpgaIrq;
 
 	/* disable interrupts on the FPGA INTC register */
-	ctrl_outl(MICRODEV_FPGA_INTC_MASK(fpgaIrq), MICRODEV_FPGA_INTDSB_REG);
+	__raw_writel(MICRODEV_FPGA_INTC_MASK(fpgaIrq), MICRODEV_FPGA_INTDSB_REG);
 }
 
 static void enable_microdev_irq(unsigned int irq)
@@ -107,13 +107,13 @@ static void enable_microdev_irq(unsigned int irq)
 	priorityReg = MICRODEV_FPGA_INTPRI_REG(fpgaIrq);
 
 	/* set priority for the interrupt */
-	priorities = ctrl_inl(priorityReg);
+	priorities = __raw_readl(priorityReg);
 	priorities &= ~MICRODEV_FPGA_INTPRI_MASK(fpgaIrq);
 	priorities |= MICRODEV_FPGA_INTPRI_LEVEL(fpgaIrq, pri);
-	ctrl_outl(priorities, priorityReg);
+	__raw_writel(priorities, priorityReg);
 
 	/* enable interrupts on the FPGA INTC register */
-	ctrl_outl(MICRODEV_FPGA_INTC_MASK(fpgaIrq), MICRODEV_FPGA_INTENB_REG);
+	__raw_writel(MICRODEV_FPGA_INTC_MASK(fpgaIrq), MICRODEV_FPGA_INTENB_REG);
 }
 
 /* This function sets the desired irq handler to be a MicroDev type */
@@ -134,7 +134,7 @@ extern void __init init_microdev_irq(void)
 	int i;
 
 	/* disable interrupts on the FPGA INTC register */
-	ctrl_outl(~0ul, MICRODEV_FPGA_INTDSB_REG);
+	__raw_writel(~0ul, MICRODEV_FPGA_INTDSB_REG);
 
 	for (i = 0; i < NUM_EXTERNAL_IRQS; i++)
 		make_microdev_irq(i);
diff --git a/arch/sh/boards/mach-migor/setup.c b/arch/sh/boards/mach-migor/setup.c
index 507c77b..ed2eeeb 100644
--- a/arch/sh/boards/mach-migor/setup.c
+++ b/arch/sh/boards/mach-migor/setup.c
@@ -516,8 +516,8 @@ static int __init migor_devices_setup(void)
 
 	/* SMC91C111 - Enable IRQ0, Setup CS4 for 16-bit fast access */
 	gpio_request(GPIO_FN_IRQ0, NULL);
-	ctrl_outl(0x00003400, BSC_CS4BCR);
-	ctrl_outl(0x00110080, BSC_CS4WCR);
+	__raw_writel(0x00003400, BSC_CS4BCR);
+	__raw_writel(0x00110080, BSC_CS4WCR);
 
 	/* KEYSC */
 	gpio_request(GPIO_FN_KEYOUT0, NULL);
@@ -533,7 +533,7 @@ static int __init migor_devices_setup(void)
 
 	/* NAND Flash */
 	gpio_request(GPIO_FN_CS6A_CE2B, NULL);
-	ctrl_outl((ctrl_inl(BSC_CS6ABCR) & ~0x0600) | 0x0200, BSC_CS6ABCR);
+	__raw_writel((__raw_readl(BSC_CS6ABCR) & ~0x0600) | 0x0200, BSC_CS6ABCR);
 	gpio_request(GPIO_PTA1, NULL);
 	gpio_direction_input(GPIO_PTA1);
 
@@ -627,7 +627,7 @@ static int __init migor_devices_setup(void)
 #else
 	gpio_direction_output(GPIO_PTT0, 1);
 #endif
-	ctrl_outw(ctrl_inw(PORT_MSELCRB) | 0x2000, PORT_MSELCRB); /* D15->D8 */
+	__raw_writew(__raw_readw(PORT_MSELCRB) | 0x2000, PORT_MSELCRB); /* D15->D8 */
 
 	platform_resource_setup_memory(&migor_ceu_device, "ceu", 4 << 20);
 
diff --git a/arch/sh/boards/mach-r2d/irq.c b/arch/sh/boards/mach-r2d/irq.c
index 78d7b27..574f009 100644
--- a/arch/sh/boards/mach-r2d/irq.c
+++ b/arch/sh/boards/mach-r2d/irq.c
@@ -129,7 +129,7 @@ void __init init_rts7751r2d_IRQ(void)
 {
 	struct intc_desc *d;
 
-	switch (ctrl_inw(PA_VERREG) & 0xf0) {
+	switch (__raw_readw(PA_VERREG) & 0xf0) {
 #ifdef CONFIG_RTS7751R2D_PLUS
 	case 0x10:
 		printk(KERN_INFO "Using R2D-PLUS interrupt controller.\n");
@@ -147,7 +147,7 @@ void __init init_rts7751r2d_IRQ(void)
 #endif
 	default:
 		printk(KERN_INFO "Unknown R2D interrupt controller 0x%04x\n",
-		       ctrl_inw(PA_VERREG));
+		       __raw_readw(PA_VERREG));
 		return;
 	}
 
diff --git a/arch/sh/boards/mach-r2d/setup.c b/arch/sh/boards/mach-r2d/setup.c
index a625ecb..b84df6a 100644
--- a/arch/sh/boards/mach-r2d/setup.c
+++ b/arch/sh/boards/mach-r2d/setup.c
@@ -70,7 +70,7 @@ static struct spi_board_info spi_bus[] = {
 static void r2d_chip_select(struct sh_spi_info *spi, int cs, int state)
 {
 	BUG_ON(cs != 0);  /* Single Epson RTC-9701JE attached on CS0 */
-	ctrl_outw(state == BITBANG_CS_ACTIVE, PA_RTCCE);
+	__raw_writew(state == BITBANG_CS_ACTIVE, PA_RTCCE);
 }
 
 static struct sh_spi_info spi_info = {
@@ -262,7 +262,7 @@ __initcall(rts7751r2d_devices_setup);
 
 static void rts7751r2d_power_off(void)
 {
-	ctrl_outw(0x0001, PA_POWOFF);
+	__raw_writew(0x0001, PA_POWOFF);
 }
 
 /*
@@ -271,14 +271,14 @@ static void rts7751r2d_power_off(void)
 static void __init rts7751r2d_setup(char **cmdline_p)
 {
 	void __iomem *sm501_reg;
-	u16 ver = ctrl_inw(PA_VERREG);
+	u16 ver = __raw_readw(PA_VERREG);
 
 	printk(KERN_INFO "Renesas Technology Sales RTS7751R2D support.\n");
 
 	printk(KERN_INFO "FPGA version:%d (revision:%d)\n",
 					(ver >> 4) & 0xf, ver & 0xf);
 
-	ctrl_outw(0x0000, PA_OUTPORT);
+	__raw_writew(0x0000, PA_OUTPORT);
 	pm_power_off = rts7751r2d_power_off;
 
 	/* sm501 dram configuration:
diff --git a/arch/sh/boards/mach-rsk/devices-rsk7203.c b/arch/sh/boards/mach-rsk/devices-rsk7203.c
index c37617e..4fa08ba 100644
--- a/arch/sh/boards/mach-rsk/devices-rsk7203.c
+++ b/arch/sh/boards/mach-rsk/devices-rsk7203.c
@@ -96,7 +96,7 @@ static int __init rsk7203_devices_setup(void)
 	gpio_request(GPIO_FN_RXD0, NULL);
 
 	/* Setup LAN9118: CS1 in 16-bit Big Endian Mode, IRQ0 at Port B */
-	ctrl_outl(0x36db0400, 0xfffc0008); /* CS1BCR */
+	__raw_writel(0x36db0400, 0xfffc0008); /* CS1BCR */
 	gpio_request(GPIO_FN_IRQ0_PB, NULL);
 
 	return platform_add_devices(rsk7203_devices,
diff --git a/arch/sh/boards/mach-sdk7780/irq.c b/arch/sh/boards/mach-sdk7780/irq.c
index 8555581..e5f7564 100644
--- a/arch/sh/boards/mach-sdk7780/irq.c
+++ b/arch/sh/boards/mach-sdk7780/irq.c
@@ -37,9 +37,9 @@ void __init init_sdk7780_IRQ(void)
 {
 	printk(KERN_INFO "Using SDK7780 interrupt controller.\n");
 
-	ctrl_outw(0xFFFF, FPGA_IRQ0MR);
+	__raw_writew(0xFFFF, FPGA_IRQ0MR);
 	/* Setup IRL 0-3 */
-	ctrl_outw(0x0003, FPGA_IMSR);
+	__raw_writew(0x0003, FPGA_IMSR);
 	plat_irq_setup_pins(IRQ_MODE_IRL3210);
 
 	register_intc_controller(&fpga_intc_desc);
diff --git a/arch/sh/boards/mach-sdk7780/setup.c b/arch/sh/boards/mach-sdk7780/setup.c
index b887373..4da38db 100644
--- a/arch/sh/boards/mach-sdk7780/setup.c
+++ b/arch/sh/boards/mach-sdk7780/setup.c
@@ -74,8 +74,8 @@ device_initcall(sdk7780_devices_setup);
 
 static void __init sdk7780_setup(char **cmdline_p)
 {
-	u16 ver = ctrl_inw(FPGA_FPVERR);
-	u16 dateStamp = ctrl_inw(FPGA_FPDATER);
+	u16 ver = __raw_readw(FPGA_FPVERR);
+	u16 dateStamp = __raw_readw(FPGA_FPDATER);
 
 	printk(KERN_INFO "Renesas Technology Europe SDK7780 support.\n");
 	printk(KERN_INFO "Board version: %d (revision %d), "
@@ -85,7 +85,7 @@ static void __init sdk7780_setup(char **cmdline_p)
 			 dateStamp);
 
 	/* Setup pin mux'ing for PCIC */
-	ctrl_outw(0x0000, GPIO_PECR);
+	__raw_writew(0x0000, GPIO_PECR);
 }
 
 /*
diff --git a/arch/sh/boards/mach-se/7206/io.c b/arch/sh/boards/mach-se/7206/io.c
index 1804556..adadc77 100644
--- a/arch/sh/boards/mach-se/7206/io.c
+++ b/arch/sh/boards/mach-se/7206/io.c
@@ -16,7 +16,7 @@
 
 static inline void delay(void)
 {
-	ctrl_inw(0x20000000);  /* P2 ROM Area */
+	__raw_readw(0x20000000);  /* P2 ROM Area */
 }
 
 /* MS7750 requires special versions of in*, out* routines, since
diff --git a/arch/sh/boards/mach-se/7206/irq.c b/arch/sh/boards/mach-se/7206/irq.c
index aef7f05..79be4bc 100644
--- a/arch/sh/boards/mach-se/7206/irq.c
+++ b/arch/sh/boards/mach-se/7206/irq.c
@@ -32,12 +32,12 @@ static void disable_se7206_irq(unsigned int irq)
 	unsigned short msk0,msk1;
 
 	/* Set the priority in IPR to 0 */
-	val = ctrl_inw(INTC_IPR01);
+	val = __raw_readw(INTC_IPR01);
 	val &= mask;
-	ctrl_outw(val, INTC_IPR01);
+	__raw_writew(val, INTC_IPR01);
 	/* FPGA mask set */
-	msk0 = ctrl_inw(INTMSK0);
-	msk1 = ctrl_inw(INTMSK1);
+	msk0 = __raw_readw(INTMSK0);
+	msk1 = __raw_readw(INTMSK1);
 
 	switch (irq) {
 	case IRQ0_IRQ:
@@ -51,8 +51,8 @@ static void disable_se7206_irq(unsigned int irq)
 		msk1 |= 0x00ff;
 		break;
 	}
-	ctrl_outw(msk0, INTMSK0);
-	ctrl_outw(msk1, INTMSK1);
+	__raw_writew(msk0, INTMSK0);
+	__raw_writew(msk1, INTMSK1);
 }
 
 static void enable_se7206_irq(unsigned int irq)
@@ -62,13 +62,13 @@ static void enable_se7206_irq(unsigned int irq)
 	unsigned short msk0,msk1;
 
 	/* Set priority in IPR back to original value */
-	val = ctrl_inw(INTC_IPR01);
+	val = __raw_readw(INTC_IPR01);
 	val |= value;
-	ctrl_outw(val, INTC_IPR01);
+	__raw_writew(val, INTC_IPR01);
 
 	/* FPGA mask reset */
-	msk0 = ctrl_inw(INTMSK0);
-	msk1 = ctrl_inw(INTMSK1);
+	msk0 = __raw_readw(INTMSK0);
+	msk1 = __raw_readw(INTMSK1);
 
 	switch (irq) {
 	case IRQ0_IRQ:
@@ -82,8 +82,8 @@ static void enable_se7206_irq(unsigned int irq)
 		msk1 &= ~0x00ff;
 		break;
 	}
-	ctrl_outw(msk0, INTMSK0);
-	ctrl_outw(msk1, INTMSK1);
+	__raw_writew(msk0, INTMSK0);
+	__raw_writew(msk1, INTMSK1);
 }
 
 static void eoi_se7206_irq(unsigned int irq)
@@ -93,8 +93,8 @@ static void eoi_se7206_irq(unsigned int irq)
 	if (!(irq_desc[irq].status & (IRQ_DISABLED|IRQ_INPROGRESS)))
 		enable_se7206_irq(irq);
 	/* FPGA isr clear */
-	sts0 = ctrl_inw(INTSTS0);
-	sts1 = ctrl_inw(INTSTS1);
+	sts0 = __raw_readw(INTSTS0);
+	sts1 = __raw_readw(INTSTS1);
 
 	switch (irq) {
 	case IRQ0_IRQ:
@@ -108,8 +108,8 @@ static void eoi_se7206_irq(unsigned int irq)
 		sts1 &= ~0x00ff;
 		break;
 	}
-	ctrl_outw(sts0, INTSTS0);
-	ctrl_outw(sts1, INTSTS1);
+	__raw_writew(sts0, INTSTS0);
+	__raw_writew(sts1, INTSTS1);
 }
 
 static struct irq_chip se7206_irq_chip __read_mostly = {
@@ -136,11 +136,11 @@ void __init init_se7206_IRQ(void)
 	make_se7206_irq(IRQ0_IRQ); /* SMC91C111 */
 	make_se7206_irq(IRQ1_IRQ); /* ATA */
 	make_se7206_irq(IRQ3_IRQ); /* SLOT / PCM */
-	ctrl_outw(inw(INTC_ICR1) | 0x000b ,INTC_ICR1 ) ; /* ICR1 */
+	__raw_writew(inw(INTC_ICR1) | 0x000b ,INTC_ICR1 ) ; /* ICR1 */
 
 	/* FPGA System register setup*/
-	ctrl_outw(0x0000,INTSTS0); /* Clear INTSTS0 */
-	ctrl_outw(0x0000,INTSTS1); /* Clear INTSTS1 */
+	__raw_writew(0x0000,INTSTS0); /* Clear INTSTS0 */
+	__raw_writew(0x0000,INTSTS1); /* Clear INTSTS1 */
 	/* IRQ0=LAN, IRQ1=ATA, IRQ3=SLT,PCM */
-	ctrl_outw(0x0001,INTSEL);
+	__raw_writew(0x0001,INTSEL);
 }
diff --git a/arch/sh/boards/mach-se/7343/irq.c b/arch/sh/boards/mach-se/7343/irq.c
index c60fd13..d4305c2 100644
--- a/arch/sh/boards/mach-se/7343/irq.c
+++ b/arch/sh/boards/mach-se/7343/irq.c
@@ -21,13 +21,13 @@ unsigned int se7343_fpga_irq[SE7343_FPGA_IRQ_NR] = { 0, };
 static void disable_se7343_irq(unsigned int irq)
 {
 	unsigned int bit = (unsigned int)get_irq_chip_data(irq);
-	ctrl_outw(ctrl_inw(PA_CPLD_IMSK) | 1 << bit, PA_CPLD_IMSK);
+	__raw_writew(__raw_readw(PA_CPLD_IMSK) | 1 << bit, PA_CPLD_IMSK);
 }
 
 static void enable_se7343_irq(unsigned int irq)
 {
 	unsigned int bit = (unsigned int)get_irq_chip_data(irq);
-	ctrl_outw(ctrl_inw(PA_CPLD_IMSK) & ~(1 << bit), PA_CPLD_IMSK);
+	__raw_writew(__raw_readw(PA_CPLD_IMSK) & ~(1 << bit), PA_CPLD_IMSK);
 }
 
 static struct irq_chip se7343_irq_chip __read_mostly = {
@@ -39,7 +39,7 @@ static struct irq_chip se7343_irq_chip __read_mostly = {
 
 static void se7343_irq_demux(unsigned int irq, struct irq_desc *desc)
 {
-	unsigned short intv = ctrl_inw(PA_CPLD_ST);
+	unsigned short intv = __raw_readw(PA_CPLD_ST);
 	unsigned int ext_irq = 0;
 
 	intv &= (1 << SE7343_FPGA_IRQ_NR) - 1;
@@ -59,8 +59,8 @@ void __init init_7343se_IRQ(void)
 {
 	int i, irq;
 
-	ctrl_outw(0, PA_CPLD_IMSK);	/* disable all irqs */
-	ctrl_outw(0x2000, 0xb03fffec);	/* mrshpc irq enable */
+	__raw_writew(0, PA_CPLD_IMSK);	/* disable all irqs */
+	__raw_writew(0x2000, 0xb03fffec);	/* mrshpc irq enable */
 
 	for (i = 0; i < SE7343_FPGA_IRQ_NR; i++) {
 		irq = create_irq();
diff --git a/arch/sh/boards/mach-se/7343/setup.c b/arch/sh/boards/mach-se/7343/setup.c
index 3412bb2..d2370af 100644
--- a/arch/sh/boards/mach-se/7343/setup.c
+++ b/arch/sh/boards/mach-se/7343/setup.c
@@ -161,10 +161,10 @@ device_initcall(sh7343se_devices_setup);
  */
 static void __init sh7343se_setup(char **cmdline_p)
 {
-	ctrl_outw(0xf900, FPGA_OUT);	/* FPGA */
+	__raw_writew(0xf900, FPGA_OUT);	/* FPGA */
 
-	ctrl_outw(0x0002, PORT_PECR);	/* PORT E 1 = IRQ5 */
-	ctrl_outw(0x0020, PORT_PSELD);
+	__raw_writew(0x0002, PORT_PECR);	/* PORT E 1 = IRQ5 */
+	__raw_writew(0x0020, PORT_PSELD);
 
 	printk(KERN_INFO "MS7343CP01 Setup...done\n");
 }
diff --git a/arch/sh/boards/mach-se/770x/irq.c b/arch/sh/boards/mach-se/770x/irq.c
index ec1fea5..1028c17 100644
--- a/arch/sh/boards/mach-se/770x/irq.c
+++ b/arch/sh/boards/mach-se/770x/irq.c
@@ -96,13 +96,13 @@ static struct ipr_desc ipr_irq_desc = {
 void __init init_se_IRQ(void)
 {
 	/* Disable all interrupts */
-	ctrl_outw(0, BCR_ILCRA);
-	ctrl_outw(0, BCR_ILCRB);
-	ctrl_outw(0, BCR_ILCRC);
-	ctrl_outw(0, BCR_ILCRD);
-	ctrl_outw(0, BCR_ILCRE);
-	ctrl_outw(0, BCR_ILCRF);
-	ctrl_outw(0, BCR_ILCRG);
+	__raw_writew(0, BCR_ILCRA);
+	__raw_writew(0, BCR_ILCRB);
+	__raw_writew(0, BCR_ILCRC);
+	__raw_writew(0, BCR_ILCRD);
+	__raw_writew(0, BCR_ILCRE);
+	__raw_writew(0, BCR_ILCRF);
+	__raw_writew(0, BCR_ILCRG);
 
 	register_ipr_controller(&ipr_irq_desc);
 }
diff --git a/arch/sh/boards/mach-se/7721/irq.c b/arch/sh/boards/mach-se/7721/irq.c
index b417acc..d85022e 100644
--- a/arch/sh/boards/mach-se/7721/irq.c
+++ b/arch/sh/boards/mach-se/7721/irq.c
@@ -38,7 +38,7 @@ static DECLARE_INTC_DESC(intc_desc, "SE7721", vectors,
 void __init init_se7721_IRQ(void)
 {
 	/* PPCR */
-	ctrl_outw(ctrl_inw(0xa4050118) & ~0x00ff, 0xa4050118);
+	__raw_writew(__raw_readw(0xa4050118) & ~0x00ff, 0xa4050118);
 
 	register_intc_controller(&intc_desc);
 	intc_set_priority(MRSHPC_IRQ0, 0xf - MRSHPC_IRQ0);
diff --git a/arch/sh/boards/mach-se/7721/setup.c b/arch/sh/boards/mach-se/7721/setup.c
index 460da53..7416ad7 100644
--- a/arch/sh/boards/mach-se/7721/setup.c
+++ b/arch/sh/boards/mach-se/7721/setup.c
@@ -80,10 +80,10 @@ device_initcall(se7721_devices_setup);
 static void __init se7721_setup(char **cmdline_p)
 {
 	/* for USB */
-	ctrl_outw(0x0000, 0xA405010C);	/* PGCR */
-	ctrl_outw(0x0000, 0xA405010E);	/* PHCR */
-	ctrl_outw(0x00AA, 0xA4050118);	/* PPCR */
-	ctrl_outw(0x0000, 0xA4050124);	/* PSELA */
+	__raw_writew(0x0000, 0xA405010C);	/* PGCR */
+	__raw_writew(0x0000, 0xA405010E);	/* PHCR */
+	__raw_writew(0x00AA, 0xA4050118);	/* PPCR */
+	__raw_writew(0x0000, 0xA4050124);	/* PSELA */
 }
 
 /*
diff --git a/arch/sh/boards/mach-se/7722/irq.c b/arch/sh/boards/mach-se/7722/irq.c
index b221b68..61605db 100644
--- a/arch/sh/boards/mach-se/7722/irq.c
+++ b/arch/sh/boards/mach-se/7722/irq.c
@@ -21,13 +21,13 @@ unsigned int se7722_fpga_irq[SE7722_FPGA_IRQ_NR] = { 0, };
 static void disable_se7722_irq(unsigned int irq)
 {
 	unsigned int bit = (unsigned int)get_irq_chip_data(irq);
-	ctrl_outw(ctrl_inw(IRQ01_MASK) | 1 << bit, IRQ01_MASK);
+	__raw_writew(__raw_readw(IRQ01_MASK) | 1 << bit, IRQ01_MASK);
 }
 
 static void enable_se7722_irq(unsigned int irq)
 {
 	unsigned int bit = (unsigned int)get_irq_chip_data(irq);
-	ctrl_outw(ctrl_inw(IRQ01_MASK) & ~(1 << bit), IRQ01_MASK);
+	__raw_writew(__raw_readw(IRQ01_MASK) & ~(1 << bit), IRQ01_MASK);
 }
 
 static struct irq_chip se7722_irq_chip __read_mostly = {
@@ -39,7 +39,7 @@ static struct irq_chip se7722_irq_chip __read_mostly = {
 
 static void se7722_irq_demux(unsigned int irq, struct irq_desc *desc)
 {
-	unsigned short intv = ctrl_inw(IRQ01_STS);
+	unsigned short intv = __raw_readw(IRQ01_STS);
 	unsigned int ext_irq = 0;
 
 	intv &= (1 << SE7722_FPGA_IRQ_NR) - 1;
@@ -59,8 +59,8 @@ void __init init_se7722_IRQ(void)
 {
 	int i, irq;
 
-	ctrl_outw(0, IRQ01_MASK);       /* disable all irqs */
-	ctrl_outw(0x2000, 0xb03fffec);  /* mrshpc irq enable */
+	__raw_writew(0, IRQ01_MASK);       /* disable all irqs */
+	__raw_writew(0x2000, 0xb03fffec);  /* mrshpc irq enable */
 
 	for (i = 0; i < SE7722_FPGA_IRQ_NR; i++) {
 		irq = create_irq();
diff --git a/arch/sh/boards/mach-se/7722/setup.c b/arch/sh/boards/mach-se/7722/setup.c
index 9367541..80a4e57 100644
--- a/arch/sh/boards/mach-se/7722/setup.c
+++ b/arch/sh/boards/mach-se/7722/setup.c
@@ -156,32 +156,32 @@ device_initcall(se7722_devices_setup);
 
 static void __init se7722_setup(char **cmdline_p)
 {
-	ctrl_outw(0x010D, FPGA_OUT);    /* FPGA */
+	__raw_writew(0x010D, FPGA_OUT);    /* FPGA */
 
-	ctrl_outw(0x0000, PORT_PECR);   /* PORT E 1 = IRQ5 ,E 0 = BS */
-	ctrl_outw(0x1000, PORT_PJCR);   /* PORT J 1 = IRQ1,J 0 =IRQ0 */
+	__raw_writew(0x0000, PORT_PECR);   /* PORT E 1 = IRQ5 ,E 0 = BS */
+	__raw_writew(0x1000, PORT_PJCR);   /* PORT J 1 = IRQ1,J 0 =IRQ0 */
 
 	/* LCDC I/O */
-	ctrl_outw(0x0020, PORT_PSELD);
+	__raw_writew(0x0020, PORT_PSELD);
 
 	/* SIOF1*/
-	ctrl_outw(0x0003, PORT_PSELB);
-	ctrl_outw(0xe000, PORT_PSELC);
-	ctrl_outw(0x0000, PORT_PKCR);
+	__raw_writew(0x0003, PORT_PSELB);
+	__raw_writew(0xe000, PORT_PSELC);
+	__raw_writew(0x0000, PORT_PKCR);
 
 	/* LCDC */
-	ctrl_outw(0x4020, PORT_PHCR);
-	ctrl_outw(0x0000, PORT_PLCR);
-	ctrl_outw(0x0000, PORT_PMCR);
-	ctrl_outw(0x0002, PORT_PRCR);
-	ctrl_outw(0x0000, PORT_PXCR);   /* LCDC,CS6A */
+	__raw_writew(0x4020, PORT_PHCR);
+	__raw_writew(0x0000, PORT_PLCR);
+	__raw_writew(0x0000, PORT_PMCR);
+	__raw_writew(0x0002, PORT_PRCR);
+	__raw_writew(0x0000, PORT_PXCR);   /* LCDC,CS6A */
 
 	/* KEYSC */
-	ctrl_outw(0x0A10, PORT_PSELA); /* BS,SHHID2 */
-	ctrl_outw(0x0000, PORT_PYCR);
-	ctrl_outw(0x0000, PORT_PZCR);
-	ctrl_outw(ctrl_inw(PORT_HIZCRA) & ~0x4000, PORT_HIZCRA);
-	ctrl_outw(ctrl_inw(PORT_HIZCRC) & ~0xc000, PORT_HIZCRC);
+	__raw_writew(0x0A10, PORT_PSELA); /* BS,SHHID2 */
+	__raw_writew(0x0000, PORT_PYCR);
+	__raw_writew(0x0000, PORT_PZCR);
+	__raw_writew(__raw_readw(PORT_HIZCRA) & ~0x4000, PORT_HIZCRA);
+	__raw_writew(__raw_readw(PORT_HIZCRC) & ~0xc000, PORT_HIZCRC);
 }
 
 /*
diff --git a/arch/sh/boards/mach-se/7724/irq.c b/arch/sh/boards/mach-se/7724/irq.c
index f76cf3b..e5e021a 100644
--- a/arch/sh/boards/mach-se/7724/irq.c
+++ b/arch/sh/boards/mach-se/7724/irq.c
@@ -72,14 +72,14 @@ static void disable_se7724_irq(unsigned int irq)
 {
 	struct fpga_irq set = get_fpga_irq(fpga2irq(irq));
 	unsigned int bit = irq - set.base;
-	ctrl_outw(ctrl_inw(set.mraddr) | 0x0001 << bit, set.mraddr);
+	__raw_writew(__raw_readw(set.mraddr) | 0x0001 << bit, set.mraddr);
 }
 
 static void enable_se7724_irq(unsigned int irq)
 {
 	struct fpga_irq set = get_fpga_irq(fpga2irq(irq));
 	unsigned int bit = irq - set.base;
-	ctrl_outw(ctrl_inw(set.mraddr) & ~(0x0001 << bit), set.mraddr);
+	__raw_writew(__raw_readw(set.mraddr) & ~(0x0001 << bit), set.mraddr);
 }
 
 static struct irq_chip se7724_irq_chip __read_mostly = {
@@ -92,7 +92,7 @@ static struct irq_chip se7724_irq_chip __read_mostly = {
 static void se7724_irq_demux(unsigned int irq, struct irq_desc *desc)
 {
 	struct fpga_irq set = get_fpga_irq(irq);
-	unsigned short intv = ctrl_inw(set.sraddr);
+	unsigned short intv = __raw_readw(set.sraddr);
 	struct irq_desc *ext_desc;
 	unsigned int ext_irq = set.base;
 
@@ -115,13 +115,13 @@ void __init init_se7724_IRQ(void)
 {
 	int i;
 
-	ctrl_outw(0xffff, IRQ0_MR);  /* mask all */
-	ctrl_outw(0xffff, IRQ1_MR);  /* mask all */
-	ctrl_outw(0xffff, IRQ2_MR);  /* mask all */
-	ctrl_outw(0x0000, IRQ0_SR);  /* clear irq */
-	ctrl_outw(0x0000, IRQ1_SR);  /* clear irq */
-	ctrl_outw(0x0000, IRQ2_SR);  /* clear irq */
-	ctrl_outw(0x002a, IRQ_MODE); /* set irq type */
+	__raw_writew(0xffff, IRQ0_MR);  /* mask all */
+	__raw_writew(0xffff, IRQ1_MR);  /* mask all */
+	__raw_writew(0xffff, IRQ2_MR);  /* mask all */
+	__raw_writew(0x0000, IRQ0_SR);  /* clear irq */
+	__raw_writew(0x0000, IRQ1_SR);  /* clear irq */
+	__raw_writew(0x0000, IRQ2_SR);  /* clear irq */
+	__raw_writew(0x002a, IRQ_MODE); /* set irq type */
 
 	for (i = 0; i < SE7724_FPGA_IRQ_NR; i++)
 		set_irq_chip_and_handler_name(SE7724_FPGA_IRQ_BASE + i,
diff --git a/arch/sh/boards/mach-se/7724/setup.c b/arch/sh/boards/mach-se/7724/setup.c
index cbfba78..242dc84 100644
--- a/arch/sh/boards/mach-se/7724/setup.c
+++ b/arch/sh/boards/mach-se/7724/setup.c
@@ -256,12 +256,12 @@ static struct platform_device ceu1_device = {
 #define FCLKACR		0xa4150008
 static void fsimck_init(struct clk *clk)
 {
-	u32 status = ctrl_inl(clk->enable_reg);
+	u32 status = __raw_readl(clk->enable_reg);
 
 	/* use external clock */
 	status &= ~0x000000ff;
 	status |= 0x00000080;
-	ctrl_outl(status, clk->enable_reg);
+	__raw_writel(status, clk->enable_reg);
 }
 
 static struct clk_ops fsimck_clk_ops = {
@@ -522,7 +522,7 @@ static int __init sh_eth_is_eeprom_ready(void)
 	int t = 10000;
 
 	while (t--) {
-		if (!ctrl_inw(EEPROM_STAT))
+		if (!__raw_readw(EEPROM_STAT))
 			return 1;
 		cpu_relax();
 	}
@@ -542,13 +542,13 @@ static void __init sh_eth_init(void)
 
 	/* read MAC addr from EEPROM */
 	for (i = 0 ; i < 3 ; i++) {
-		ctrl_outw(0x0, EEPROM_OP); /* read */
-		ctrl_outw(i*2, EEPROM_ADR);
-		ctrl_outw(0x1, EEPROM_STRT);
+		__raw_writew(0x0, EEPROM_OP); /* read */
+		__raw_writew(i*2, EEPROM_ADR);
+		__raw_writew(0x1, EEPROM_STRT);
 		if (!sh_eth_is_eeprom_ready())
 			return;
 
-		mac = ctrl_inw(EEPROM_DATA);
+		mac = __raw_readw(EEPROM_DATA);
 		sh_eth_plat.mac_addr[i << 1] = mac & 0xff;
 		sh_eth_plat.mac_addr[(i << 1) + 1] = mac >> 8;
 	}
@@ -585,7 +585,7 @@ arch_initcall(arch_setup);
 
 static int __init devices_setup(void)
 {
-	u16 sw = ctrl_inw(SW4140); /* select camera, monitor */
+	u16 sw = __raw_readw(SW4140); /* select camera, monitor */
 	struct clk *fsia_clk;
 
 	/* register board specific self-refresh code */
@@ -595,7 +595,7 @@ static int __init devices_setup(void)
 					&ms7724se_sdram_leave_start,
 					&ms7724se_sdram_leave_end);
 	/* Reset Release */
-	ctrl_outw(ctrl_inw(FPGA_OUT) &
+	__raw_writew(__raw_readw(FPGA_OUT) &
 		  ~((1 << 1)  | /* LAN */
 		    (1 << 6)  | /* VIDEO DAC */
 		    (1 << 7)  | /* AK4643 */
@@ -604,7 +604,7 @@ static int __init devices_setup(void)
 		  FPGA_OUT);
 
 	/* turn on USB clocks, use external clock */
-	ctrl_outw((ctrl_inw(PORT_MSELCRB) & ~0xc000) | 0x8000, PORT_MSELCRB);
+	__raw_writew((__raw_readw(PORT_MSELCRB) & ~0xc000) | 0x8000, PORT_MSELCRB);
 
 #ifdef CONFIG_PM
 	/* Let LED9 show STATUS2 */
@@ -633,10 +633,10 @@ static int __init devices_setup(void)
 #endif
 
 	/* enable USB0 port */
-	ctrl_outw(0x0600, 0xa40501d4);
+	__raw_writew(0x0600, 0xa40501d4);
 
 	/* enable USB1 port */
-	ctrl_outw(0x0600, 0xa4050192);
+	__raw_writew(0x0600, 0xa4050192);
 
 	/* enable IRQ 0,1,2 */
 	gpio_request(GPIO_FN_INTC_IRQ0, NULL);
@@ -684,7 +684,7 @@ static int __init devices_setup(void)
 	gpio_request(GPIO_FN_LCDVCPWC, NULL);
 	gpio_request(GPIO_FN_LCDRD,    NULL);
 	gpio_request(GPIO_FN_LCDLCLK,  NULL);
-	ctrl_outw((ctrl_inw(PORT_HIZA) & ~0x0001), PORT_HIZA);
+	__raw_writew((__raw_readw(PORT_HIZA) & ~0x0001), PORT_HIZA);
 
 	/* enable CEU0 */
 	gpio_request(GPIO_FN_VIO0_D15, NULL);
diff --git a/arch/sh/boards/mach-se/7780/irq.c b/arch/sh/boards/mach-se/7780/irq.c
index 121744c..d5c9edc 100644
--- a/arch/sh/boards/mach-se/7780/irq.c
+++ b/arch/sh/boards/mach-se/7780/irq.c
@@ -24,30 +24,30 @@
 void __init init_se7780_IRQ(void)
 {
 	/* enable all interrupt at FPGA */
-	ctrl_outw(0, FPGA_INTMSK1);
+	__raw_writew(0, FPGA_INTMSK1);
 	/* mask SM501 interrupt */
-	ctrl_outw((ctrl_inw(FPGA_INTMSK1) | 0x0002), FPGA_INTMSK1);
+	__raw_writew((__raw_readw(FPGA_INTMSK1) | 0x0002), FPGA_INTMSK1);
 	/* enable all interrupt at FPGA */
-	ctrl_outw(0, FPGA_INTMSK2);
+	__raw_writew(0, FPGA_INTMSK2);
 
 	/* set FPGA INTSEL register */
 	/* FPGA + 0x06 */
-	ctrl_outw( ((IRQPIN_SM501 << IRQPOS_SM501) |
+	__raw_writew( ((IRQPIN_SM501 << IRQPOS_SM501) |
 		(IRQPIN_SMC91CX << IRQPOS_SMC91CX)), FPGA_INTSEL1);
 
 	/* FPGA + 0x08 */
-	ctrl_outw(((IRQPIN_EXTINT4 << IRQPOS_EXTINT4) |
+	__raw_writew(((IRQPIN_EXTINT4 << IRQPOS_EXTINT4) |
 		(IRQPIN_EXTINT3 << IRQPOS_EXTINT3) |
 		(IRQPIN_EXTINT2 << IRQPOS_EXTINT2) |
 		(IRQPIN_EXTINT1 << IRQPOS_EXTINT1)), FPGA_INTSEL2);
 
 	/* FPGA + 0x0A */
-	ctrl_outw((IRQPIN_PCCPW << IRQPOS_PCCPW), FPGA_INTSEL3);
+	__raw_writew((IRQPIN_PCCPW << IRQPOS_PCCPW), FPGA_INTSEL3);
 
 	plat_irq_setup_pins(IRQ_MODE_IRQ); /* install handlers for IRQ0-7 */
 
 	/* ICR1: detect low level(for 2ndcut) */
-	ctrl_outl(0xAAAA0000, INTC_ICR1);
+	__raw_writel(0xAAAA0000, INTC_ICR1);
 
 	/*
 	 * FPGA PCISEL register initialize
@@ -63,6 +63,6 @@ void __init init_se7780_IRQ(void)
 	 *  INTD || INTD  | INTC  |  --   | INTA
 	 *  -------------------------------------
 	 */
-	ctrl_outw(0x0013, FPGA_PCI_INTSEL1);
-	ctrl_outw(0xE402, FPGA_PCI_INTSEL2);
+	__raw_writew(0x0013, FPGA_PCI_INTSEL1);
+	__raw_writew(0xE402, FPGA_PCI_INTSEL2);
 }
diff --git a/arch/sh/boards/mach-se/7780/setup.c b/arch/sh/boards/mach-se/7780/setup.c
index f7bfb3f..6f7c207 100644
--- a/arch/sh/boards/mach-se/7780/setup.c
+++ b/arch/sh/boards/mach-se/7780/setup.c
@@ -75,14 +75,14 @@ device_initcall(se7780_devices_setup);
 static void __init se7780_setup(char **cmdline_p)
 {
 	/* "SH-Linux" on LED Display */
-	ctrl_outw( 'S' , PA_LED_DISP + (DISP_SEL0_ADDR << 1) );
-	ctrl_outw( 'H' , PA_LED_DISP + (DISP_SEL1_ADDR << 1) );
-	ctrl_outw( '-' , PA_LED_DISP + (DISP_SEL2_ADDR << 1) );
-	ctrl_outw( 'L' , PA_LED_DISP + (DISP_SEL3_ADDR << 1) );
-	ctrl_outw( 'i' , PA_LED_DISP + (DISP_SEL4_ADDR << 1) );
-	ctrl_outw( 'n' , PA_LED_DISP + (DISP_SEL5_ADDR << 1) );
-	ctrl_outw( 'u' , PA_LED_DISP + (DISP_SEL6_ADDR << 1) );
-	ctrl_outw( 'x' , PA_LED_DISP + (DISP_SEL7_ADDR << 1) );
+	__raw_writew( 'S' , PA_LED_DISP + (DISP_SEL0_ADDR << 1) );
+	__raw_writew( 'H' , PA_LED_DISP + (DISP_SEL1_ADDR << 1) );
+	__raw_writew( '-' , PA_LED_DISP + (DISP_SEL2_ADDR << 1) );
+	__raw_writew( 'L' , PA_LED_DISP + (DISP_SEL3_ADDR << 1) );
+	__raw_writew( 'i' , PA_LED_DISP + (DISP_SEL4_ADDR << 1) );
+	__raw_writew( 'n' , PA_LED_DISP + (DISP_SEL5_ADDR << 1) );
+	__raw_writew( 'u' , PA_LED_DISP + (DISP_SEL6_ADDR << 1) );
+	__raw_writew( 'x' , PA_LED_DISP + (DISP_SEL7_ADDR << 1) );
 
 	printk(KERN_INFO "Hitachi UL Solutions Engine 7780SE03 support.\n");
 
@@ -93,15 +93,15 @@ static void __init se7780_setup(char **cmdline_p)
 	 *   REQ2/GNT2 -> Serial ATA
 	 *   REQ3/GNT3 -> PCI slot
 	 */
-	ctrl_outw(0x0213, FPGA_REQSEL);
+	__raw_writew(0x0213, FPGA_REQSEL);
 
 	/* GPIO setting */
-	ctrl_outw(0x0000, GPIO_PECR);
-	ctrl_outw(ctrl_inw(GPIO_PHCR)&0xfff3, GPIO_PHCR);
-	ctrl_outw(0x0c00, GPIO_PMSELR);
+	__raw_writew(0x0000, GPIO_PECR);
+	__raw_writew(__raw_readw(GPIO_PHCR)&0xfff3, GPIO_PHCR);
+	__raw_writew(0x0c00, GPIO_PMSELR);
 
 	/* iVDR Power ON */
-	ctrl_outw(0x0001, FPGA_IVDRPW);
+	__raw_writew(0x0001, FPGA_IVDRPW);
 }
 
 /*
diff --git a/arch/sh/boards/mach-sh03/rtc.c b/arch/sh/boards/mach-sh03/rtc.c
index a8b9f84..1b20099 100644
--- a/arch/sh/boards/mach-sh03/rtc.c
+++ b/arch/sh/boards/mach-sh03/rtc.c
@@ -44,15 +44,15 @@ unsigned long get_cmos_time(void)
 	spin_lock(&sh03_rtc_lock);
  again:
 	do {
-		sec  = (ctrl_inb(RTC_SEC1) & 0xf) + (ctrl_inb(RTC_SEC10) & 0x7) * 10;
-		min  = (ctrl_inb(RTC_MIN1) & 0xf) + (ctrl_inb(RTC_MIN10) & 0xf) * 10;
-		hour = (ctrl_inb(RTC_HOU1) & 0xf) + (ctrl_inb(RTC_HOU10) & 0xf) * 10;
-		day  = (ctrl_inb(RTC_DAY1) & 0xf) + (ctrl_inb(RTC_DAY10) & 0xf) * 10;
-		mon  = (ctrl_inb(RTC_MON1) & 0xf) + (ctrl_inb(RTC_MON10) & 0xf) * 10;
-		year = (ctrl_inb(RTC_YEA1) & 0xf) + (ctrl_inb(RTC_YEA10) & 0xf) * 10
-		     + (ctrl_inb(RTC_YEA100 ) & 0xf) * 100
-		     + (ctrl_inb(RTC_YEA1000) & 0xf) * 1000;
-	} while (sec != (ctrl_inb(RTC_SEC1) & 0xf) + (ctrl_inb(RTC_SEC10) & 0x7) * 10);
+		sec  = (__raw_readb(RTC_SEC1) & 0xf) + (__raw_readb(RTC_SEC10) & 0x7) * 10;
+		min  = (__raw_readb(RTC_MIN1) & 0xf) + (__raw_readb(RTC_MIN10) & 0xf) * 10;
+		hour = (__raw_readb(RTC_HOU1) & 0xf) + (__raw_readb(RTC_HOU10) & 0xf) * 10;
+		day  = (__raw_readb(RTC_DAY1) & 0xf) + (__raw_readb(RTC_DAY10) & 0xf) * 10;
+		mon  = (__raw_readb(RTC_MON1) & 0xf) + (__raw_readb(RTC_MON10) & 0xf) * 10;
+		year = (__raw_readb(RTC_YEA1) & 0xf) + (__raw_readb(RTC_YEA10) & 0xf) * 10
+		     + (__raw_readb(RTC_YEA100 ) & 0xf) * 100
+		     + (__raw_readb(RTC_YEA1000) & 0xf) * 1000;
+	} while (sec != (__raw_readb(RTC_SEC1) & 0xf) + (__raw_readb(RTC_SEC10) & 0x7) * 10);
 	if (year == 0 || mon < 1 || mon > 12 || day > 31 || day < 1 ||
 	    hour > 23 || min > 59 || sec > 59) {
 		printk(KERN_ERR
@@ -60,16 +60,16 @@ unsigned long get_cmos_time(void)
 		printk("year=%d, mon=%d, day=%d, hour=%d, min=%d, sec=%d\n",
 		       year, mon, day, hour, min, sec);
 
-		ctrl_outb(0, RTC_SEC1); ctrl_outb(0, RTC_SEC10);
-		ctrl_outb(0, RTC_MIN1); ctrl_outb(0, RTC_MIN10);
-		ctrl_outb(0, RTC_HOU1); ctrl_outb(0, RTC_HOU10);
-		ctrl_outb(6, RTC_WEE1);
-		ctrl_outb(1, RTC_DAY1); ctrl_outb(0, RTC_DAY10);
-		ctrl_outb(1, RTC_MON1); ctrl_outb(0, RTC_MON10);
-		ctrl_outb(0, RTC_YEA1); ctrl_outb(0, RTC_YEA10);
-		ctrl_outb(0, RTC_YEA100);
-		ctrl_outb(2, RTC_YEA1000);
-		ctrl_outb(0, RTC_CTL);
+		__raw_writeb(0, RTC_SEC1); __raw_writeb(0, RTC_SEC10);
+		__raw_writeb(0, RTC_MIN1); __raw_writeb(0, RTC_MIN10);
+		__raw_writeb(0, RTC_HOU1); __raw_writeb(0, RTC_HOU10);
+		__raw_writeb(6, RTC_WEE1);
+		__raw_writeb(1, RTC_DAY1); __raw_writeb(0, RTC_DAY10);
+		__raw_writeb(1, RTC_MON1); __raw_writeb(0, RTC_MON10);
+		__raw_writeb(0, RTC_YEA1); __raw_writeb(0, RTC_YEA10);
+		__raw_writeb(0, RTC_YEA100);
+		__raw_writeb(2, RTC_YEA1000);
+		__raw_writeb(0, RTC_CTL);
 		goto again;
 	}
 
@@ -93,9 +93,9 @@ static int set_rtc_mmss(unsigned long nowtime)
 	/* gets recalled with irq locally disabled */
 	spin_lock(&sh03_rtc_lock);
 	for (i = 0 ; i < 1000000 ; i++)	/* may take up to 1 second... */
-		if (!(ctrl_inb(RTC_CTL) & RTC_BUSY))
+		if (!(__raw_readb(RTC_CTL) & RTC_BUSY))
 			break;
-	cmos_minutes = (ctrl_inb(RTC_MIN1) & 0xf) + (ctrl_inb(RTC_MIN10) & 0xf) * 10;
+	cmos_minutes = (__raw_readb(RTC_MIN1) & 0xf) + (__raw_readb(RTC_MIN10) & 0xf) * 10;
 	real_seconds = nowtime % 60;
 	real_minutes = nowtime / 60;
 	if (((abs(real_minutes - cmos_minutes) + 15)/30) & 1)
@@ -103,10 +103,10 @@ static int set_rtc_mmss(unsigned long nowtime)
 	real_minutes %= 60;
 
 	if (abs(real_minutes - cmos_minutes) < 30) {
-		ctrl_outb(real_seconds % 10, RTC_SEC1);
-		ctrl_outb(real_seconds / 10, RTC_SEC10);
-		ctrl_outb(real_minutes % 10, RTC_MIN1);
-		ctrl_outb(real_minutes / 10, RTC_MIN10);
+		__raw_writeb(real_seconds % 10, RTC_SEC1);
+		__raw_writeb(real_seconds / 10, RTC_SEC10);
+		__raw_writeb(real_minutes % 10, RTC_MIN1);
+		__raw_writeb(real_minutes / 10, RTC_MIN10);
 	} else {
 		printk(KERN_WARNING
 		       "set_rtc_mmss: can't update from %d to %d\n",
diff --git a/arch/sh/boards/mach-sh7763rdp/irq.c b/arch/sh/boards/mach-sh7763rdp/irq.c
index d8ebfa7..add698c 100644
--- a/arch/sh/boards/mach-sh7763rdp/irq.c
+++ b/arch/sh/boards/mach-sh7763rdp/irq.c
@@ -28,18 +28,18 @@
 void __init init_sh7763rdp_IRQ(void)
 {
 	/* GPIO enabled */
-	ctrl_outl(1 << 25, INTC_INT2MSKCR);
+	__raw_writel(1 << 25, INTC_INT2MSKCR);
 
 	/* enable GPIO interrupts */
-	ctrl_outl((ctrl_inl(INTC_INT2PRI7) & 0xFF00FFFF) | 0x000F0000,
+	__raw_writel((__raw_readl(INTC_INT2PRI7) & 0xFF00FFFF) | 0x000F0000,
 		  INTC_INT2PRI7);
 
 	/* USBH enabled */
-	ctrl_outl(1 << 17, INTC_INT2MSKCR1);
+	__raw_writel(1 << 17, INTC_INT2MSKCR1);
 
 	/* GETHER enabled */
-	ctrl_outl(1 << 16, INTC_INT2MSKCR1);
+	__raw_writel(1 << 16, INTC_INT2MSKCR1);
 
 	/* DMAC enabled */
-	ctrl_outl(1 << 8, INTC_INT2MSKCR);
+	__raw_writel(1 << 8, INTC_INT2MSKCR);
 }
diff --git a/arch/sh/boards/mach-sh7763rdp/setup.c b/arch/sh/boards/mach-sh7763rdp/setup.c
index 390534a..f64a691 100644
--- a/arch/sh/boards/mach-sh7763rdp/setup.c
+++ b/arch/sh/boards/mach-sh7763rdp/setup.c
@@ -158,50 +158,50 @@ device_initcall(sh7763rdp_devices_setup);
 static void __init sh7763rdp_setup(char **cmdline_p)
 {
 	/* Board version check */
-	if (ctrl_inw(CPLD_BOARD_ID_ERV_REG) == 0xECB1)
+	if (__raw_readw(CPLD_BOARD_ID_ERV_REG) == 0xECB1)
 		printk(KERN_INFO "RTE Standard Configuration\n");
 	else
 		printk(KERN_INFO "RTA Standard Configuration\n");
 
 	/* USB pin select bits (clear bit 5-2 to 0) */
-	ctrl_outw((ctrl_inw(PORT_PSEL2) & 0xFFC3), PORT_PSEL2);
+	__raw_writew((__raw_readw(PORT_PSEL2) & 0xFFC3), PORT_PSEL2);
 	/* USBH setup port I controls to other (clear bits 4-9 to 0) */
-	ctrl_outw(ctrl_inw(PORT_PICR) & 0xFC0F, PORT_PICR);
+	__raw_writew(__raw_readw(PORT_PICR) & 0xFC0F, PORT_PICR);
 
 	/* Select USB Host controller */
-	ctrl_outw(0x00, USB_USBHSC);
+	__raw_writew(0x00, USB_USBHSC);
 
 	/* For LCD */
 	/* set PTJ7-1, bits 15-2 of PJCR to 0 */
-	ctrl_outw(ctrl_inw(PORT_PJCR) & 0x0003, PORT_PJCR);
+	__raw_writew(__raw_readw(PORT_PJCR) & 0x0003, PORT_PJCR);
 	/* set PTI5, bits 11-10 of PICR to 0 */
-	ctrl_outw(ctrl_inw(PORT_PICR) & 0xF3FF, PORT_PICR);
-	ctrl_outw(0, PORT_PKCR);
-	ctrl_outw(0, PORT_PLCR);
+	__raw_writew(__raw_readw(PORT_PICR) & 0xF3FF, PORT_PICR);
+	__raw_writew(0, PORT_PKCR);
+	__raw_writew(0, PORT_PLCR);
 	/* set PSEL2 bits 14-8, 5-4, of PSEL2 to 0 */
-	ctrl_outw((ctrl_inw(PORT_PSEL2) & 0x00C0), PORT_PSEL2);
+	__raw_writew((__raw_readw(PORT_PSEL2) & 0x00C0), PORT_PSEL2);
 	/* set PSEL3 bits 14-12, 6-4, 2-0 of PSEL3 to 0 */
-	ctrl_outw((ctrl_inw(PORT_PSEL3) & 0x0700), PORT_PSEL3);
+	__raw_writew((__raw_readw(PORT_PSEL3) & 0x0700), PORT_PSEL3);
 
 	/* For HAC */
 	/* bit3-0  0100:HAC & SSI1 enable */
-	ctrl_outw((ctrl_inw(PORT_PSEL1) & 0xFFF0) | 0x0004, PORT_PSEL1);
+	__raw_writew((__raw_readw(PORT_PSEL1) & 0xFFF0) | 0x0004, PORT_PSEL1);
 	/* bit14      1:SSI_HAC_CLK enable */
-	ctrl_outw(ctrl_inw(PORT_PSEL4) | 0x4000, PORT_PSEL4);
+	__raw_writew(__raw_readw(PORT_PSEL4) | 0x4000, PORT_PSEL4);
 
 	/* SH-Ether */
-	ctrl_outw((ctrl_inw(PORT_PSEL1) & ~0xff00) | 0x2400, PORT_PSEL1);
-	ctrl_outw(0x0, PORT_PFCR);
-	ctrl_outw(0x0, PORT_PFCR);
-	ctrl_outw(0x0, PORT_PFCR);
+	__raw_writew((__raw_readw(PORT_PSEL1) & ~0xff00) | 0x2400, PORT_PSEL1);
+	__raw_writew(0x0, PORT_PFCR);
+	__raw_writew(0x0, PORT_PFCR);
+	__raw_writew(0x0, PORT_PFCR);
 
 	/* MMC */
 	/*selects SCIF and MMC other functions */
-	ctrl_outw(0x0001, PORT_PSEL0);
+	__raw_writew(0x0001, PORT_PSEL0);
 	/* MMC clock operates */
-	ctrl_outl(ctrl_inl(MSTPCR1) & ~0x8, MSTPCR1);
-	ctrl_outw(ctrl_inw(PORT_PACR) & ~0x3000, PORT_PACR);
-	ctrl_outw(ctrl_inw(PORT_PCCR) & ~0xCFC3, PORT_PCCR);
+	__raw_writel(__raw_readl(MSTPCR1) & ~0x8, MSTPCR1);
+	__raw_writew(__raw_readw(PORT_PACR) & ~0x3000, PORT_PACR);
+	__raw_writew(__raw_readw(PORT_PCCR) & ~0xCFC3, PORT_PCCR);
 }
 
 static struct sh_machine_vector mv_sh7763rdp __initmv = {
diff --git a/arch/sh/boards/mach-snapgear/setup.c b/arch/sh/boards/mach-snapgear/setup.c
index a3277a2..331745d 100644
--- a/arch/sh/boards/mach-snapgear/setup.c
+++ b/arch/sh/boards/mach-snapgear/setup.c
@@ -30,7 +30,7 @@
 
 static irqreturn_t eraseconfig_interrupt(int irq, void *dev_id)
 {
-	(void)ctrl_inb(0xb8000000);	/* dummy read */
+	(void)__raw_readb(0xb8000000);	/* dummy read */
 
 	printk("SnapGear: erase switch interrupt!\n");
 
diff --git a/arch/sh/boards/mach-systemh/irq.c b/arch/sh/boards/mach-systemh/irq.c
index 986a0e7..523aea5 100644
--- a/arch/sh/boards/mach-systemh/irq.c
+++ b/arch/sh/boards/mach-systemh/irq.c
@@ -41,13 +41,13 @@ static void disable_systemh_irq(unsigned int irq)
 		unsigned long val, mask = 0x01 << 1;
 
 		/* Clear the "irq"th bit in the mask and set it in the request */
-		val = ctrl_inl((unsigned long)systemh_irq_mask_register);
+		val = __raw_readl((unsigned long)systemh_irq_mask_register);
 		val &= ~mask;
-		ctrl_outl(val, (unsigned long)systemh_irq_mask_register);
+		__raw_writel(val, (unsigned long)systemh_irq_mask_register);
 
-		val = ctrl_inl((unsigned long)systemh_irq_request_register);
+		val = __raw_readl((unsigned long)systemh_irq_request_register);
 		val |= mask;
-		ctrl_outl(val, (unsigned long)systemh_irq_request_register);
+		__raw_writel(val, (unsigned long)systemh_irq_request_register);
 	}
 }
 
@@ -57,9 +57,9 @@ static void enable_systemh_irq(unsigned int irq)
 		unsigned long val, mask = 0x01 << 1;
 
 		/* Set "irq"th bit in the mask register */
-		val = ctrl_inl((unsigned long)systemh_irq_mask_register);
+		val = __raw_readl((unsigned long)systemh_irq_mask_register);
 		val |= mask;
-		ctrl_outl(val, (unsigned long)systemh_irq_mask_register);
+		__raw_writel(val, (unsigned long)systemh_irq_mask_register);
 	}
 }
 
diff --git a/arch/sh/boards/mach-titan/io.c b/arch/sh/boards/mach-titan/io.c
index 0130e98..29754c5 100644
--- a/arch/sh/boards/mach-titan/io.c
+++ b/arch/sh/boards/mach-titan/io.c
@@ -16,8 +16,8 @@ static inline unsigned int port2adr(unsigned int port)
 u8 titan_inb(unsigned long port)
 {
         if (PXSEG(port))
-                return ctrl_inb(port);
-        return ctrl_inw(port2adr(port)) & 0xff;
+                return __raw_readb(port);
+        return __raw_readw(port2adr(port)) & 0xff;
 }
 
 u8 titan_inb_p(unsigned long port)
@@ -25,9 +25,9 @@ u8 titan_inb_p(unsigned long port)
         u8 v;
 
         if (PXSEG(port))
-                v = ctrl_inb(port);
+                v = __raw_readb(port);
         else
-                v = ctrl_inw(port2adr(port)) & 0xff;
+                v = __raw_readw(port2adr(port)) & 0xff;
         ctrl_delay();
         return v;
 }
@@ -35,9 +35,9 @@ u8 titan_inb_p(unsigned long port)
 u16 titan_inw(unsigned long port)
 {
         if (PXSEG(port))
-                return ctrl_inw(port);
+                return __raw_readw(port);
         else if (port >= 0x2000)
-                return ctrl_inw(port2adr(port));
+                return __raw_readw(port2adr(port));
         else
                 maybebadio(port);
         return 0;
@@ -46,9 +46,9 @@ u16 titan_inw(unsigned long port)
 u32 titan_inl(unsigned long port)
 {
         if (PXSEG(port))
-                return ctrl_inl(port);
+                return __raw_readl(port);
         else if (port >= 0x2000)
-                return ctrl_inw(port2adr(port));
+                return __raw_readw(port2adr(port));
         else
                 maybebadio(port);
         return 0;
@@ -57,26 +57,26 @@ u32 titan_inl(unsigned long port)
 void titan_outb(u8 value, unsigned long port)
 {
         if (PXSEG(port))
-                ctrl_outb(value, port);
+                __raw_writeb(value, port);
         else
-                ctrl_outw(value, port2adr(port));
+                __raw_writew(value, port2adr(port));
 }
 
 void titan_outb_p(u8 value, unsigned long port)
 {
         if (PXSEG(port))
-                ctrl_outb(value, port);
+                __raw_writeb(value, port);
         else
-                ctrl_outw(value, port2adr(port));
+                __raw_writew(value, port2adr(port));
         ctrl_delay();
 }
 
 void titan_outw(u16 value, unsigned long port)
 {
         if (PXSEG(port))
-                ctrl_outw(value, port);
+                __raw_writew(value, port);
         else if (port >= 0x2000)
-                ctrl_outw(value, port2adr(port));
+                __raw_writew(value, port2adr(port));
         else
                 maybebadio(port);
 }
@@ -84,7 +84,7 @@ void titan_outw(u16 value, unsigned long port)
 void titan_outl(u32 value, unsigned long port)
 {
         if (PXSEG(port))
-                ctrl_outl(value, port);
+                __raw_writel(value, port);
         else
                 maybebadio(port);
 }
diff --git a/arch/sh/boards/mach-x3proto/ilsel.c b/arch/sh/boards/mach-x3proto/ilsel.c
index b5c673c..5c98427 100644
--- a/arch/sh/boards/mach-x3proto/ilsel.c
+++ b/arch/sh/boards/mach-x3proto/ilsel.c
@@ -70,10 +70,10 @@ static void __ilsel_enable(ilsel_source_t set, unsigned int bit)
 	pr_debug("%s: bit#%d: addr - 0x%08lx (shift %d, set %d)\n",
 		 __func__, bit, addr, shift, set);
 
-	tmp = ctrl_inw(addr);
+	tmp = __raw_readw(addr);
 	tmp &= ~(0xf << shift);
 	tmp |= set << shift;
-	ctrl_outw(tmp, addr);
+	__raw_writew(tmp, addr);
 }
 
 /**
@@ -142,9 +142,9 @@ void ilsel_disable(unsigned int irq)
 
 	addr = mk_ilsel_addr(irq);
 
-	tmp = ctrl_inw(addr);
+	tmp = __raw_readw(addr);
 	tmp &= ~(0xf << mk_ilsel_shift(irq));
-	ctrl_outw(tmp, addr);
+	__raw_writew(tmp, addr);
 
 	clear_bit(irq, &ilsel_level_map);
 }
diff --git a/arch/sh/boards/mach-x3proto/setup.c b/arch/sh/boards/mach-x3proto/setup.c
index efe4cb9..e284592 100644
--- a/arch/sh/boards/mach-x3proto/setup.c
+++ b/arch/sh/boards/mach-x3proto/setup.c
@@ -149,7 +149,7 @@ static void __init x3proto_init_irq(void)
 	plat_irq_setup_pins(IRQ_MODE_IRL3210);
 
 	/* Set ICR0.LVLMODE */
-	ctrl_outl(ctrl_inl(0xfe410000) | (1 << 21), 0xfe410000);
+	__raw_writel(__raw_readl(0xfe410000) | (1 << 21), 0xfe410000);
 }
 
 static struct sh_machine_vector mv_x3proto __initmv = {