Merge branch 'avr32-arch' of git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6

* 'avr32-arch' of git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6:
  avr32: add hardware handshake support to atmel_serial
  avr32: add RTS/CTS/CLK pin selection for the USARTs
  Add RTC support for Merisc boards
  avr32: at32ap700x: setup DMA for AC97C in the machine code
  avr32: at32ap700x: setup DMA for ABDAC in the machine code
  Add Merisc board support
  avr32: use gpio_is_valid() to check USBA vbus_pin I/O line
  atmel-usba-udc: use gpio_is_valid() to check vbus_pin I/O line
  avr32: fix timing LCD parameters for EVKLCD10X boards
  avr32: use GPIO line PB15 on EVKLCD10x boards for backlight
  avr32: configure MCI detect and write protect pins for EVKLCD10x boards
  avr32: set pin mask to alternative 18 bpp for EVKLCD10x boards
  avr32: add pin mask for 18-bit color on the LCD controller
  avr32: fix 15-bit LCDC pin mask to use MSB lines

1 files changed, 7 insertions, 7 deletions

diff --git a/drivers/usb/gadget/atmel_usba_udc.c b/drivers/usb/gadget/atmel_usba_udc.c
index c22fab1..563d572 100644
--- a/drivers/usb/gadget/atmel_usba_udc.c
+++ b/drivers/usb/gadget/atmel_usba_udc.c
@@ -319,7 +319,7 @@ static inline void usba_cleanup_debugfs(struct usba_udc *udc)
 
 static int vbus_is_present(struct usba_udc *udc)
 {
-	if (udc->vbus_pin != -1)
+	if (gpio_is_valid(udc->vbus_pin))
 		return gpio_get_value(udc->vbus_pin);
 
 	/* No Vbus detection: Assume always present */
@@ -1821,7 +1821,7 @@ int usb_gadget_register_driver(struct usb_gadget_driver *driver)
 	DBG(DBG_GADGET, "registered driver `%s'\n", driver->driver.name);
 
 	udc->vbus_prev = 0;
-	if (udc->vbus_pin != -1)
+	if (gpio_is_valid(udc->vbus_pin))
 		enable_irq(gpio_to_irq(udc->vbus_pin));
 
 	/* If Vbus is present, enable the controller and wait for reset */
@@ -1852,7 +1852,7 @@ int usb_gadget_unregister_driver(struct usb_gadget_driver *driver)
 	if (driver != udc->driver || !driver->unbind)
 		return -EINVAL;
 
-	if (udc->vbus_pin != -1)
+	if (gpio_is_valid(udc->vbus_pin))
 		disable_irq(gpio_to_irq(udc->vbus_pin));
 
 	spin_lock_irqsave(&udc->lock, flags);
@@ -1910,7 +1910,7 @@ static int __init usba_udc_probe(struct platform_device *pdev)
 	udc->pdev = pdev;
 	udc->pclk = pclk;
 	udc->hclk = hclk;
-	udc->vbus_pin = -1;
+	udc->vbus_pin = -ENODEV;
 
 	ret = -ENOMEM;
 	udc->regs = ioremap(regs->start, regs->end - regs->start + 1);
@@ -1996,7 +1996,7 @@ static int __init usba_udc_probe(struct platform_device *pdev)
 		goto err_device_add;
 	}
 
-	if (pdata->vbus_pin >= 0) {
+	if (gpio_is_valid(pdata->vbus_pin)) {
 		if (!gpio_request(pdata->vbus_pin, "atmel_usba_udc")) {
 			udc->vbus_pin = pdata->vbus_pin;
 
@@ -2005,7 +2005,7 @@ static int __init usba_udc_probe(struct platform_device *pdev)
 					"atmel_usba_udc", udc);
 			if (ret) {
 				gpio_free(udc->vbus_pin);
-				udc->vbus_pin = -1;
+				udc->vbus_pin = -ENODEV;
 				dev_warn(&udc->pdev->dev,
 					 "failed to request vbus irq; "
 					 "assuming always on\n");
@@ -2051,7 +2051,7 @@ static int __exit usba_udc_remove(struct platform_device *pdev)
 		usba_ep_cleanup_debugfs(&usba_ep[i]);
 	usba_cleanup_debugfs(udc);
 
-	if (udc->vbus_pin != -1)
+	if (gpio_is_valid(udc->vbus_pin))
 		gpio_free(udc->vbus_pin);
 
 	free_irq(udc->irq, udc);