fbdev: platforming metronomefb and am200epd

This patch splits metronomefb into the platform independent metronomefb and
the platform dependent am200epd.

Signed-off-by: Jaya Kumar <jayakumar.lkml@gmail.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

1 files changed, 295 insertions, 0 deletions

diff --git a/drivers/video/am200epd.c b/drivers/video/am200epd.c
new file mode 100644
index 0000000..51e26c1
--- /dev/null
+++ b/drivers/video/am200epd.c
@@ -0,0 +1,295 @@
+/*
+ * linux/drivers/video/am200epd.c -- Platform device for AM200 EPD kit
+ *
+ * Copyright (C) 2008, Jaya Kumar
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file COPYING in the main directory of this archive for
+ * more details.
+ *
+ * Layout is based on skeletonfb.c by James Simmons and Geert Uytterhoeven.
+ *
+ * This work was made possible by help and equipment support from E-Ink
+ * Corporation. http://support.eink.com/community
+ *
+ * This driver is written to be used with the Metronome display controller.
+ * on the AM200 EPD prototype kit/development kit with an E-Ink 800x600
+ * Vizplex EPD on a Gumstix board using the Lyre interface board.
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/errno.h>
+#include <linux/string.h>
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/fb.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/list.h>
+#include <linux/uaccess.h>
+#include <linux/irq.h>
+
+#include <video/metronomefb.h>
+
+#include <asm/arch/pxa-regs.h>
+
+/* register offsets for gpio control */
+#define LED_GPIO_PIN 51
+#define STDBY_GPIO_PIN 48
+#define RST_GPIO_PIN 49
+#define RDY_GPIO_PIN 32
+#define ERR_GPIO_PIN 17
+#define PCBPWR_GPIO_PIN 16
+
+#define AF_SEL_GPIO_N 0x3
+#define GAFR0_U_OFFSET(pin) ((pin - 16) * 2)
+#define GAFR1_L_OFFSET(pin) ((pin - 32) * 2)
+#define GAFR1_U_OFFSET(pin) ((pin - 48) * 2)
+#define GPDR1_OFFSET(pin) (pin - 32)
+#define GPCR1_OFFSET(pin) (pin - 32)
+#define GPSR1_OFFSET(pin) (pin - 32)
+#define GPCR0_OFFSET(pin) (pin)
+#define GPSR0_OFFSET(pin) (pin)
+
+static void am200_set_gpio_output(int pin, int val)
+{
+	u8 index;
+
+	index = pin >> 4;
+
+	switch (index) {
+	case 1:
+		if (val)
+			GPSR0 |= (1 << GPSR0_OFFSET(pin));
+		else
+			GPCR0 |= (1 << GPCR0_OFFSET(pin));
+		break;
+	case 2:
+		break;
+	case 3:
+		if (val)
+			GPSR1 |= (1 << GPSR1_OFFSET(pin));
+		else
+			GPCR1 |= (1 << GPCR1_OFFSET(pin));
+		break;
+	default:
+		printk(KERN_ERR "unimplemented\n");
+	}
+}
+
+static void __devinit am200_init_gpio_pin(int pin, int dir)
+{
+	u8 index;
+	/* dir 0 is output, 1 is input
+	- do 2 things here:
+	- set gpio alternate function to standard gpio
+	- set gpio direction to input or output  */
+
+	index = pin >> 4;
+	switch (index) {
+	case 1:
+		GAFR0_U &= ~(AF_SEL_GPIO_N << GAFR0_U_OFFSET(pin));
+
+		if (dir)
+			GPDR0 &= ~(1 << pin);
+		else
+			GPDR0 |= (1 << pin);
+		break;
+	case 2:
+		GAFR1_L &= ~(AF_SEL_GPIO_N << GAFR1_L_OFFSET(pin));
+
+		if (dir)
+			GPDR1 &= ~(1 << GPDR1_OFFSET(pin));
+		else
+			GPDR1 |= (1 << GPDR1_OFFSET(pin));
+		break;
+	case 3:
+		GAFR1_U &= ~(AF_SEL_GPIO_N << GAFR1_U_OFFSET(pin));
+
+		if (dir)
+			GPDR1 &= ~(1 << GPDR1_OFFSET(pin));
+		else
+			GPDR1 |= (1 << GPDR1_OFFSET(pin));
+		break;
+	default:
+		printk(KERN_ERR "unimplemented\n");
+	}
+}
+
+static void am200_init_gpio_regs(struct metronomefb_par *par)
+{
+	am200_init_gpio_pin(LED_GPIO_PIN, 0);
+	am200_set_gpio_output(LED_GPIO_PIN, 0);
+
+	am200_init_gpio_pin(STDBY_GPIO_PIN, 0);
+	am200_set_gpio_output(STDBY_GPIO_PIN, 0);
+
+	am200_init_gpio_pin(RST_GPIO_PIN, 0);
+	am200_set_gpio_output(RST_GPIO_PIN, 0);
+
+	am200_init_gpio_pin(RDY_GPIO_PIN, 1);
+
+	am200_init_gpio_pin(ERR_GPIO_PIN, 1);
+
+	am200_init_gpio_pin(PCBPWR_GPIO_PIN, 0);
+	am200_set_gpio_output(PCBPWR_GPIO_PIN, 0);
+}
+
+static void am200_disable_lcd_controller(struct metronomefb_par *par)
+{
+	LCSR = 0xffffffff;	/* Clear LCD Status Register */
+	LCCR0 |= LCCR0_DIS;	/* Disable LCD Controller */
+
+	/* we reset and just wait for things to settle */
+	msleep(200);
+}
+
+static void am200_enable_lcd_controller(struct metronomefb_par *par)
+{
+	LCSR = 0xffffffff;
+	FDADR0 = par->metromem_desc_dma;
+	LCCR0 |= LCCR0_ENB;
+}
+
+static void am200_init_lcdc_regs(struct metronomefb_par *par)
+{
+	/* here we do:
+	- disable the lcd controller
+	- setup lcd control registers
+	- setup dma descriptor
+	- reenable lcd controller
+	*/
+
+	/* disable the lcd controller */
+	am200_disable_lcd_controller(par);
+
+	/* setup lcd control registers */
+	LCCR0 = LCCR0_LDM | LCCR0_SFM | LCCR0_IUM | LCCR0_EFM | LCCR0_PAS
+		| LCCR0_QDM | LCCR0_BM | LCCR0_OUM;
+
+	LCCR1 = (par->info->var.xres/2 - 1) /* pixels per line */
+		| (27 << 10) /* hsync pulse width - 1 */
+		| (33 << 16) /* eol pixel count */
+		| (33 << 24); /* bol pixel count */
+
+	LCCR2 = (par->info->var.yres - 1) /* lines per panel */
+		| (24 << 10) /* vsync pulse width - 1 */
+		| (2 << 16) /* eof pixel count */
+		| (0 << 24); /* bof pixel count */
+
+	LCCR3 = 2 /* pixel clock divisor */
+		| (24 << 8) /* AC Bias pin freq */
+		| LCCR3_16BPP /* BPP */
+		| LCCR3_PCP;  /* PCP falling edge */
+
+}
+
+static void am200_post_dma_setup(struct metronomefb_par *par)
+{
+	par->metromem_desc->mFDADR0 = par->metromem_desc_dma;
+	par->metromem_desc->mFSADR0 = par->metromem_dma;
+	par->metromem_desc->mFIDR0 = 0;
+	par->metromem_desc->mLDCMD0 = par->info->var.xres
+					* par->info->var.yres;
+	am200_enable_lcd_controller(par);
+}
+
+static void am200_free_irq(struct fb_info *info)
+{
+	free_irq(IRQ_GPIO(RDY_GPIO_PIN), info);
+}
+
+static irqreturn_t am200_handle_irq(int irq, void *dev_id)
+{
+	struct fb_info *info = dev_id;
+	struct metronomefb_par *par = info->par;
+
+	wake_up_interruptible(&par->waitq);
+	return IRQ_HANDLED;
+}
+
+static int am200_setup_irq(struct fb_info *info)
+{
+	int retval;
+
+	retval = request_irq(IRQ_GPIO(RDY_GPIO_PIN), am200_handle_irq,
+				IRQF_DISABLED, "AM200", info);
+	if (retval) {
+		printk(KERN_ERR "am200epd: request_irq failed: %d\n", retval);
+		return retval;
+	}
+
+	return set_irq_type(IRQ_GPIO(RDY_GPIO_PIN), IRQT_FALLING);
+}
+
+static void am200_set_rst(struct metronomefb_par *par, int state)
+{
+	am200_set_gpio_output(RST_GPIO_PIN, state);
+}
+
+static void am200_set_stdby(struct metronomefb_par *par, int state)
+{
+	am200_set_gpio_output(STDBY_GPIO_PIN, state);
+}
+
+static int am200_wait_event(struct metronomefb_par *par)
+{
+	return wait_event_timeout(par->waitq, (GPLR1 & 0x01), HZ);
+}
+
+static int am200_wait_event_intr(struct metronomefb_par *par)
+{
+	return wait_event_interruptible_timeout(par->waitq, (GPLR1 & 0x01), HZ);
+}
+
+static struct metronome_board am200_board = {
+	.owner			= THIS_MODULE,
+	.free_irq		= am200_free_irq,
+	.setup_irq		= am200_setup_irq,
+	.init_gpio_regs		= am200_init_gpio_regs,
+	.init_lcdc_regs		= am200_init_lcdc_regs,
+	.post_dma_setup		= am200_post_dma_setup,
+	.set_rst		= am200_set_rst,
+	.set_stdby		= am200_set_stdby,
+	.met_wait_event		= am200_wait_event,
+	.met_wait_event_intr	= am200_wait_event_intr,
+};
+
+static struct platform_device *am200_device;
+
+static int __init am200_init(void)
+{
+	int ret;
+
+	/* request our platform independent driver */
+	request_module("metronomefb");
+
+	am200_device = platform_device_alloc("metronomefb", -1);
+	if (!am200_device)
+		return -ENOMEM;
+
+	platform_device_add_data(am200_device, &am200_board,
+					sizeof(am200_board));
+
+	/* this _add binds metronomefb to am200. metronomefb refcounts am200 */
+	ret = platform_device_add(am200_device);
+
+	if (ret)
+		platform_device_put(am200_device);
+
+	return ret;
+}
+
+static void __exit am200_exit(void)
+{
+	platform_device_unregister(am200_device);
+}
+
+module_init(am200_init);
+module_exit(am200_exit);
+
+MODULE_DESCRIPTION("board driver for am200 metronome epd kit");
+MODULE_AUTHOR("Jaya Kumar");
+MODULE_LICENSE("GPL");