1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
|
Device-mapper snapshot support
==============================
Device-mapper allows you, without massive data copying:
*) To create snapshots of any block device i.e. mountable, saved states of
the block device which are also writable without interfering with the
original content;
*) To create device "forks", i.e. multiple different versions of the
same data stream.
*) To merge a snapshot of a block device back into the snapshot's origin
device.
In the first two cases, dm copies only the chunks of data that get
changed and uses a separate copy-on-write (COW) block device for
storage.
For snapshot merge the contents of the COW storage are merged back into
the origin device.
There are three dm targets available:
snapshot, snapshot-origin, and snapshot-merge.
*) snapshot-origin <origin>
which will normally have one or more snapshots based on it.
Reads will be mapped directly to the backing device. For each write, the
original data will be saved in the <COW device> of each snapshot to keep
its visible content unchanged, at least until the <COW device> fills up.
*) snapshot <origin> <COW device> <persistent?> <chunksize>
A snapshot of the <origin> block device is created. Changed chunks of
<chunksize> sectors will be stored on the <COW device>. Writes will
only go to the <COW device>. Reads will come from the <COW device> or
from <origin> for unchanged data. <COW device> will often be
smaller than the origin and if it fills up the snapshot will become
useless and be disabled, returning errors. So it is important to monitor
the amount of free space and expand the <COW device> before it fills up.
<persistent?> is P (Persistent) or N (Not persistent - will not survive
after reboot).
The difference is that for transient snapshots less metadata must be
saved on disk - they can be kept in memory by the kernel.
* snapshot-merge <origin> <COW device> <persistent> <chunksize>
takes the same table arguments as the snapshot target except it only
works with persistent snapshots. This target assumes the role of the
"snapshot-origin" target and must not be loaded if the "snapshot-origin"
is still present for <origin>.
Creates a merging snapshot that takes control of the changed chunks
stored in the <COW device> of an existing snapshot, through a handover
procedure, and merges these chunks back into the <origin>. Once merging
has started (in the background) the <origin> may be opened and the merge
will continue while I/O is flowing to it. Changes to the <origin> are
deferred until the merging snapshot's corresponding chunk(s) have been
merged. Once merging has started the snapshot device, associated with
the "snapshot" target, will return -EIO when accessed.
How snapshot is used by LVM2
============================
When you create the first LVM2 snapshot of a volume, four dm devices are used:
1) a device containing the original mapping table of the source volume;
2) a device used as the <COW device>;
3) a "snapshot" device, combining #1 and #2, which is the visible snapshot
volume;
4) the "original" volume (which uses the device number used by the original
source volume), whose table is replaced by a "snapshot-origin" mapping
from device #1.
A fixed naming scheme is used, so with the following commands:
lvcreate -L 1G -n base volumeGroup
lvcreate -L 100M --snapshot -n snap volumeGroup/base
we'll have this situation (with volumes in above order):
# dmsetup table|grep volumeGroup
volumeGroup-base-real: 0 2097152 linear 8:19 384
volumeGroup-snap-cow: 0 204800 linear 8:19 2097536
volumeGroup-snap: 0 2097152 snapshot 254:11 254:12 P 16
volumeGroup-base: 0 2097152 snapshot-origin 254:11
# ls -lL /dev/mapper/volumeGroup-*
brw------- 1 root root 254, 11 29 ago 18:15 /dev/mapper/volumeGroup-base-real
brw------- 1 root root 254, 12 29 ago 18:15 /dev/mapper/volumeGroup-snap-cow
brw------- 1 root root 254, 13 29 ago 18:15 /dev/mapper/volumeGroup-snap
brw------- 1 root root 254, 10 29 ago 18:14 /dev/mapper/volumeGroup-base
How snapshot-merge is used by LVM2
==================================
A merging snapshot assumes the role of the "snapshot-origin" while
merging. As such the "snapshot-origin" is replaced with
"snapshot-merge". The "-real" device is not changed and the "-cow"
device is renamed to <origin name>-cow to aid LVM2's cleanup of the
merging snapshot after it completes. The "snapshot" that hands over its
COW device to the "snapshot-merge" is deactivated (unless using lvchange
--refresh); but if it is left active it will simply return I/O errors.
A snapshot will merge into its origin with the following command:
lvconvert --merge volumeGroup/snap
we'll now have this situation:
# dmsetup table|grep volumeGroup
volumeGroup-base-real: 0 2097152 linear 8:19 384
volumeGroup-base-cow: 0 204800 linear 8:19 2097536
volumeGroup-base: 0 2097152 snapshot-merge 254:11 254:12 P 16
# ls -lL /dev/mapper/volumeGroup-*
brw------- 1 root root 254, 11 29 ago 18:15 /dev/mapper/volumeGroup-base-real
brw------- 1 root root 254, 12 29 ago 18:16 /dev/mapper/volumeGroup-base-cow
brw------- 1 root root 254, 10 29 ago 18:16 /dev/mapper/volumeGroup-base
|
