1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
|
/*
*
* 2.6 port, Embedded Alley Solutions, Inc
*
* Based on Per Hallsmark, per.hallsmark@mvista.com
*
* This program is free software; you can distribute it and/or modify it
* under the terms of the GNU General Public License (Version 2) as
* published by the Free Software Foundation.
*
* This program is distributed in the hope it will be useful, but WITHOUT
* ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
* FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
* for more details.
*
* You should have received a copy of the GNU General Public License along
* with this program; if not, write to the Free Software Foundation, Inc.,
* 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
*/
#include <linux/init.h>
#include <linux/sched.h>
#include <linux/ioport.h>
#include <linux/irq.h>
#include <linux/mm.h>
#include <linux/delay.h>
#include <linux/interrupt.h>
#include <linux/serial_pnx8xxx.h>
#include <linux/pm.h>
#include <asm/cpu.h>
#include <asm/bootinfo.h>
#include <asm/irq.h>
#include <asm/mipsregs.h>
#include <asm/reboot.h>
#include <asm/pgtable.h>
#include <asm/time.h>
#include <glb.h>
#include <int.h>
#include <pci.h>
#include <uart.h>
#include <nand.h>
extern void __init board_setup(void);
extern void pnx8550_machine_restart(char *);
extern void pnx8550_machine_halt(void);
extern void pnx8550_machine_power_off(void);
extern struct resource ioport_resource;
extern struct resource iomem_resource;
extern char *prom_getcmdline(void);
struct resource standard_io_resources[] = {
{
.start = 0x00,
.end = 0x1f,
.name = "dma1",
.flags = IORESOURCE_BUSY
}, {
.start = 0x40,
.end = 0x5f,
.name = "timer",
.flags = IORESOURCE_BUSY
}, {
.start = 0x80,
.end = 0x8f,
.name = "dma page reg",
.flags = IORESOURCE_BUSY
}, {
.start = 0xc0,
.end = 0xdf,
.name = "dma2",
.flags = IORESOURCE_BUSY
},
};
#define STANDARD_IO_RESOURCES ARRAY_SIZE(standard_io_resources)
extern struct resource pci_io_resource;
extern struct resource pci_mem_resource;
/* Return the total size of DRAM-memory, (RANK0 + RANK1) */
unsigned long get_system_mem_size(void)
{
/* Read IP2031_RANK0_ADDR_LO */
unsigned long dram_r0_lo = inl(PCI_BASE | 0x65010);
/* Read IP2031_RANK1_ADDR_HI */
unsigned long dram_r1_hi = inl(PCI_BASE | 0x65018);
return dram_r1_hi - dram_r0_lo + 1;
}
int pnx8550_console_port = -1;
void __init plat_mem_setup(void)
{
int i;
char* argptr;
board_setup(); /* board specific setup */
_machine_restart = pnx8550_machine_restart;
_machine_halt = pnx8550_machine_halt;
pm_power_off = pnx8550_machine_power_off;
/* Clear the Global 2 Register, PCI Inta Output Enable Registers
Bit 1:Enable DAC Powerdown
-> 0:DACs are enabled and are working normally
1:DACs are powerdown
Bit 0:Enable of PCI inta output
-> 0 = Disable PCI inta output
1 = Enable PCI inta output
*/
PNX8550_GLB2_ENAB_INTA_O = 0;
/* IO/MEM resources. */
set_io_port_base(PNX8550_PORT_BASE);
ioport_resource.start = 0;
ioport_resource.end = ~0;
iomem_resource.start = 0;
iomem_resource.end = ~0;
/* Request I/O space for devices on this board */
for (i = 0; i < STANDARD_IO_RESOURCES; i++)
request_resource(&ioport_resource, standard_io_resources + i);
/* Place the Mode Control bit for GPIO pin 16 in primary function */
/* Pin 16 is used by UART1, UA1_TX */
outl((PNX8550_GPIO_MODE_PRIMOP << PNX8550_GPIO_MC_16_BIT) |
(PNX8550_GPIO_MODE_PRIMOP << PNX8550_GPIO_MC_17_BIT),
PNX8550_GPIO_MC1);
argptr = prom_getcmdline();
if ((argptr = strstr(argptr, "console=ttyS")) != NULL) {
argptr += strlen("console=ttyS");
pnx8550_console_port = *argptr == '0' ? 0 : 1;
/* We must initialize the UART (console) before early printk */
/* Set LCR to 8-bit and BAUD to 38400 (no 5) */
ip3106_lcr(UART_BASE, pnx8550_console_port) =
PNX8XXX_UART_LCR_8BIT;
ip3106_baud(UART_BASE, pnx8550_console_port) = 5;
}
return;
}
|
