blob: bc9684e66a84f0cb83366acb7ebef430109d5770 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
|
/*
* Yucca board definitions
*
* Roland Dreier <rolandd@cisco.com> (based on luan.h by Matt Porter)
*
* Copyright 2004-2005 MontaVista Software Inc.
* Copyright (c) 2005 Cisco Systems. All rights reserved.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License, or (at your
* option) any later version.
*
*/
#ifdef __KERNEL__
#ifndef __ASM_YUCCA_H__
#define __ASM_YUCCA_H__
#include <platforms/4xx/ppc440spe.h>
/* F/W TLB mapping used in bootloader glue to reset EMAC */
#define PPC44x_EMAC0_MR0 0xa0000800
/* Location of MAC addresses in PIBS image */
#define PIBS_FLASH_BASE 0xffe00000
#define PIBS_MAC_BASE (PIBS_FLASH_BASE+0x1b0400)
/* External timer clock frequency */
#define YUCCA_TMR_CLK 25000000
/*
* FPGA registers
*/
#define YUCCA_FPGA_REG_BASE 0x00000004e2000000ULL
#define YUCCA_FPGA_REG_SIZE 0x24
#define FPGA_REG1A 0x1a
#define FPGA_REG1A_PE0_GLED 0x8000
#define FPGA_REG1A_PE1_GLED 0x4000
#define FPGA_REG1A_PE2_GLED 0x2000
#define FPGA_REG1A_PE0_YLED 0x1000
#define FPGA_REG1A_PE1_YLED 0x0800
#define FPGA_REG1A_PE2_YLED 0x0400
#define FPGA_REG1A_PE0_PWRON 0x0200
#define FPGA_REG1A_PE1_PWRON 0x0100
#define FPGA_REG1A_PE2_PWRON 0x0080
#define FPGA_REG1A_PE0_REFCLK_ENABLE 0x0040
#define FPGA_REG1A_PE1_REFCLK_ENABLE 0x0020
#define FPGA_REG1A_PE2_REFCLK_ENABLE 0x0010
#define FPGA_REG1A_PE_SPREAD0 0x0008
#define FPGA_REG1A_PE_SPREAD1 0x0004
#define FPGA_REG1A_PE_SELSOURCE_0 0x0002
#define FPGA_REG1A_PE_SELSOURCE_1 0x0001
#define FPGA_REG1C 0x1c
#define FPGA_REG1C_PE0_ROOTPOINT 0x8000
#define FPGA_REG1C_PE1_ENDPOINT 0x4000
#define FPGA_REG1C_PE2_ENDPOINT 0x2000
#define FPGA_REG1C_PE0_PRSNT 0x1000
#define FPGA_REG1C_PE1_PRSNT 0x0800
#define FPGA_REG1C_PE2_PRSNT 0x0400
#define FPGA_REG1C_PE0_WAKE 0x0080
#define FPGA_REG1C_PE1_WAKE 0x0040
#define FPGA_REG1C_PE2_WAKE 0x0020
#define FPGA_REG1C_PE0_PERST 0x0010
#define FPGA_REG1C_PE1_PERST 0x0008
#define FPGA_REG1C_PE2_PERST 0x0004
/*
* Serial port defines
*/
#define RS_TABLE_SIZE 3
/* PIBS defined UART mappings, used before early_serial_setup */
#define UART0_IO_BASE 0xa0000200
#define UART1_IO_BASE 0xa0000300
#define UART2_IO_BASE 0xa0000600
#define BASE_BAUD 11059200
#define STD_UART_OP(num) \
{ 0, BASE_BAUD, 0, UART##num##_INT, \
(ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST), \
iomem_base: (void*)UART##num##_IO_BASE, \
io_type: SERIAL_IO_MEM},
#define SERIAL_PORT_DFNS \
STD_UART_OP(0) \
STD_UART_OP(1) \
STD_UART_OP(2)
/* PCI support */
#define YUCCA_PCIX_LOWER_IO 0x00000000
#define YUCCA_PCIX_UPPER_IO 0x0000ffff
#define YUCCA_PCIX_LOWER_MEM 0x80000000
#define YUCCA_PCIX_UPPER_MEM 0x8fffffff
#define YUCCA_PCIE_LOWER_MEM 0x90000000
#define YUCCA_PCIE_MEM_SIZE 0x10000000
#define YUCCA_PCIX_MEM_SIZE 0x10000000
#define YUCCA_PCIX_MEM_OFFSET 0x00000000
#define YUCCA_PCIE_MEM_SIZE 0x10000000
#define YUCCA_PCIE_MEM_OFFSET 0x00000000
#endif /* __ASM_YUCCA_H__ */
#endif /* __KERNEL__ */
|
