diff options
| -rw-r--r-- | device.mk | 2 | ||||
| -rw-r--r-- | mxt224_ts_input.idc | 52 | ||||
| -rw-r--r-- | qt602240_ts_input.idc | 53 |
3 files changed, 53 insertions, 54 deletions
@@ -121,7 +121,7 @@ PRODUCT_PACKAGES += \ # Input device calibration files PRODUCT_COPY_FILES += \ - device/samsung/crespo/qt602240_ts_input.idc:system/usr/idc/qt602240_ts_input.idc + device/samsung/crespo/mxt224_ts_input.idc:system/usr/idc/mxt224_ts_input.idc # These are the hardware-specific features PRODUCT_COPY_FILES += \ diff --git a/mxt224_ts_input.idc b/mxt224_ts_input.idc new file mode 100644 index 0000000..f754999 --- /dev/null +++ b/mxt224_ts_input.idc @@ -0,0 +1,52 @@ +# Copyright (C) 2010 The Android Open Source Project +# +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +# +# Input Device Calibration File for the Crespo touch screen. +# +# These calibration values are derived from empirical measurements +# and may not be appropriate for use with other touch screens. +# Refer to the input device calibration documentation for more details. +# + +# Touch Size +touch.touchSize.calibration = pressure + +# Tool Size +# Driver reports tool size as an area measurement. +# +# Based on empirical measurements, we estimate the size of the tool +# using size = sqrt(22 * rawToolArea + 0) * 9.2 + 0. +touch.toolSize.calibration = area +touch.toolSize.areaScale = 22 +touch.toolSize.areaBias = 0 +touch.toolSize.linearScale = 9.2 +touch.toolSize.linearBias = 0 +touch.toolSize.isSummed = 0 + +# Pressure +# Driver reports signal strength as pressure. +# +# A normal thumb touch typically registers about 100 signal strength +# units although we don't expect these values to be accurate. +touch.pressure.calibration = amplitude +touch.pressure.source = default +touch.pressure.scale = 0.01 + +# Size +touch.size.calibration = normalized + +# Orientation +touch.orientation.calibration = none + diff --git a/qt602240_ts_input.idc b/qt602240_ts_input.idc deleted file mode 100644 index bed1e8a..0000000 --- a/qt602240_ts_input.idc +++ /dev/null @@ -1,53 +0,0 @@ -# Copyright (C) 2010 The Android Open Source Project -# -# Licensed under the Apache License, Version 2.0 (the "License"); -# you may not use this file except in compliance with the License. -# You may obtain a copy of the License at -# -# http://www.apache.org/licenses/LICENSE-2.0 -# -# Unless required by applicable law or agreed to in writing, software -# distributed under the License is distributed on an "AS IS" BASIS, -# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. -# See the License for the specific language governing permissions and -# limitations under the License. - -# -# Input Device Calibration File -# - -# Touch Area -touch.touchArea.calibration = pressure - -# Tool Area -# Raw width field measures approx. 0.5 units per millimeter -# of tool area on the surface where a raw width of 15 corresponds -# to about 18mm of physical size. Given that the display resolution -# is 9.6px per mm we obtain a scale factor of 4.8 pixels / unit and -# a bias of 100.8 pixels. Each contact point is measured independently -# so the raw width is not a sum. -touch.toolArea.calibration = linear -touch.toolArea.linearScale = 4.8 -touch.toolArea.linearBias = 100.8 -touch.toolArea.isSummed = 0 - -# Pressure -# Driver reports signal strength as pressure. -# A normal thumb touch while touching the back of the device -# typically registers about 40 signal strength units although -# this value is highly variable and is sensitive to contact area, -# manner of contact and environmental conditions. We set the -# scale so that a normal touch with good signal strength will be -# reported as having a pressure somewhere in the vicinity of 1.0, -# a featherlight touch will be below 1.0 and a heavy or large touch -# will be above 1.0. We don't expect these values to be accurate. -touch.pressure.calibration = amplitude -touch.pressure.source = default -touch.pressure.scale = 0.025 - -# Size -touch.size.calibration = normalized - -# Orientation -touch.orientation.calibration = none - |